-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT BILLET BMW N54/N55/S55 Crank Seal Guard
$84.99 – $179.99Price range: $84.99 through $179.99VTT BILLET BMW N54/55 Crank Seal Guard.
It is a well-known issue on the BMW N54/N55/S55 platforms that your serpentine belt can fail for various reasons, when this happens you have a high chance of the belt getting sucked behind the front damper, and then being pushed past the crank seal into your oil pan. From there it can get sucked into the oil pick up causing total engine failure, even if you do not lose the engine it is a COSTLY repair to remove the sub-frame and drop the oil pan to remove the belt. The best way to combat this is to watch for oil leaks and keep up on your maintenance. BUT Even with those preventative measures, pre-mature belt failure can occur. This crank seal guard installs over your front crank seal and will keep the belt from being sucked in if a belt failure does occur. This is a cheap way to ensure you do not end up having to replace your motor from oil starvation due to an ingested belt. Our seal is different from those already on the market, firstly it is not offensively priced. Secondly, it is 100% billet, with no welds on the tabs to break, no cheap bent thin steel pieces. 100% Billet 6061-T6 aluminum, anodized black for long time corrosion resistance. Crank Seal comes with- One VTT Billet N54/55 Crank Seal Guard
- Two extended 12.9 Grade bolts, and two stainless washers
-
Quick View
VTT S55 / N55 Crank Bolt Capture
$127.49The VTT S55 crank bolt capture. slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub, meaning it cannot back out no matter what. -
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVTT BMW Billet One Way Crankcase Breather VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, and remove crankcase pressure, all while adding a cool look to your engine bay. Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one-way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.This breather will fit MOST NOT ALL BMWs with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54, S85, S63, S63TU, N63. There are factors that may stop it from fitting your platform such as valve cover style etc.
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / Details -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT N55/S55 “Spline Lock” Crank Hub Solution
$819.99 – $939.99Price range: $819.99 through $939.99VTT āSpline Lockā Crank Hub System ā N54 / N55 / S55
VTT is proud to offer theĀ only complete crank hub solutionĀ for BMW N54, N55, and S55 engines thatĀ does not require drilling the crankshaft for pins.
Our innovative hub features proprietaryĀ Spline Lock Technologyāa high-tolerance, precision-machined spline system that presses into the crank andĀ positively locks the hub in place, eliminating the need for traditional pinning or welding.
After months of rigorous development and over 10 different prototype revisions, our final production version was put to the test. In our in-house trials, the hub outperformed expectationsābreaking our testing rig before it ever slipped. Real-world validation has been conducted on the VTT N54 race car, which spins toĀ 8,000 RPMĀ and produces overĀ 900 WHP.
Key Benefits:
-
No crank drilling requiredĀ ā stock-like installation
-
Minimal laborĀ ā fully reversible with no permanent modification
-
Tested to extreme conditionsĀ ā race-proven at high RPM and power
-
Exclusively compatible with VTTās Crank Bolt Capture (CBC)Ā for maximum security
ā ļøĀ Spline Lock hubs are recommended be used with the VTT Crank Bolt Capture system. They are not intended to run independently.
-
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Ignition Coil Kits
$169.99 – $222.49Price range: $169.99 through $222.49VTT is proud to offer ignition coil replacements for the N5X platforms, as well as B5X, and many VAG platforms. We started our quest for coils by contacting multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once we were satisfied with the testing, we had the best performing coils made to our colors and specs. We offer these coils as complete sets for the N54, B58/S58, and the VAG platforms in either 4, or 5 cylinders. We also offer upgraded plugs which are highly recommended to change when doing coil replacements These coils come in 3 colors, Red, Black, and Blue, and are not simply an aesthetic upgrade but match or exceed the factory secondary spark energy. The VAG coil, is extremely potent, and the tester was so impressed with it compared to the factory coil, he called it a "BEAST" of a coilNote:Ā To extract maximum performance from VTT coils minor tune changes are required to optimize dwell periods. See recommended Dwell times below
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA well-known issue with the N54 and early N55 with Hydraulic power steering is the plastic pulley either hitting the subframe, or simply breaking on its own, this can cause the belt to be ejected from the pulley, and leave you stranded with no serpentine belt. To top it off if you continue to run the vehicle with the belt off, you also have a good chance of sucking the belt into the engine through the front seal. Put an end to the dreaded plastic PS pulley issues with our 100% Billet Aluminum PS pulley. We make these from 6061-T6 aluminum and anodize them in one of 4 colors (Black, Red, Blue, and Clear) for a great look, and long-lasting finish. These weigh 11Oz, very close to the weight of a stock pulley, and are lighter than the cast aluminum versions on the market. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT BMW/Toyota Conversion Wheel Spacers
$59.99 – $74.99Price range: $59.99 through $74.99Looking to convert your 5Ć120 or 5x112 vehicle to 5x114.3 wheels, or 5x120 wheels, and open up your wheel options DRAMATICALLY? We got covered with our VTT wheel spacer conversion kits. These kits are machined from billet 6061-T6 aluminum and anodized for a long-lasting finish. We then press in 10.9 class studs, with corrosion-resistant zinc coating for years of use. The spacer then accepts either a 5x114 wheel or a 5x120 wheel. The 5x114 use M14 studs, and the 5x120 use M12 studs. All the spacers have either a 66.6mm or 72.6mm Hub bore size to fit 99% of BMW applications, and we offer Hub-Centric adapter rings to fit other wheel bore sizes No wobble bolts or redrilling here. We offer these in 4 thicknesses 15mm, 17.5mm, 20mm, and 25mm. The studs coming out of the spacer areĀ 40ā³ total length and come with Black Lugnuts. Spacers that convert to 5x120 have M12 studs, ALL others have M14x1.5 -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT-FAB Billet Oil/Coolant Fittings, and block offs
$21.99 – $41.99Price range: $21.99 through $41.99VTT Universal Turbo Fittings ā Oil & Coolant Solutions for BMW Turbo Builds!
Looking to fabricate your own turbo kit for BMW platforms? Need an easy solution to block off water lines or create custom feed and drain fittings? Look no further! VTT offers a wide range of high-quality oil and coolant fittings to simplify your build. Our fittings are designed for most late-model BMW platforms, providing a plug-and-play solution for custom turbo setups. š Available Fitting Options: š¹ Oil Feed ā -4 AN Male š¹ Oil Drain ā -10 AN Male š¹ Coolant Fittings ā Barbed Male or Block-Off Options -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Cold Side Charge Pipe
$94.99 – $127.49Price range: $94.99 through $127.49Whenever upgrading your N54 we suggest going to a true BOV like a Turbosmart Raceport. This cold side charge pipe allows you to do that while getting rid of the prone to cracking plastic charge pipe, and plastic DV's. If you do want to keep the DV set up, we also offer a DV charge pipe. Also available for N55 with no bungs at all, as the DV is on the turbo. Looking for the Charge Pipe & BOV Combo? Click Here -
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / Details-
Introducing the VTT OBD-LOCKĀ ā Enhanced Security & Improved Design!
We are excited to announce our OBD-LOCK! This latest version has been completely redesigned for improved strength, ease of installation, and enhanced protection. Key upgrades include:
ā No more OBD port penetration ā eliminates any risk of damage
ā Revised thread style ā prevents stripping for a secure fit
ā Stronger, more durable design ā ensures maximum securityUltimate OBD Port Protection
The VTT OBD-LOCK is precision-machined from billet 6061-T6 aluminum and is engineered to completely lock out your OBD port, preventing unauthorized access.
š Anti-Theft Protection ā Prevents thieves from accessing the OBD port to duplicate keys or disable security systems
š Dealer/Tech Lockout ā Stops unauthorized tune changes or system modifications
š Tamper-Proof Design ā Cannot be removed without physically destroying the OBD port unless the correct tool is usedVTT OBD-LOCK ā Version 2 NON-GM
Universal Fit for All Non-GM (General Motors) VehiclesThis device is compatible with all non-GM vehicles, including but not limited to:
-
All VAG group vehicles (VW, Audi, Bentley, etc.) ā including recessed port VW/Audi models
-
Ford, Nissan, Honda, Toyota, Porsche, Dodge, Ram, Jeep, Kia, Subaru, and more
Not compatible with GM (General Motors) vehicles.
VTT OBD-LOCK ā Version 2 GM
Universal Fit for GM (General Motors) Vehicles ONLYThis version is specifically designed for General Motors vehicles, including GM, Chevrolet, Cadillac, Holden, and other GM-branded models.
If your vehicle is anything other than a General Motors product, you will need the Non-GM version.
-
-
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT BMW Billet Coolant Reservoir Cap
$79.99 – $189.99Price range: $79.99 through $189.99VTT is proud to offer our billet replacement for the factory plastic Coolant Reservoir cap. This cap does away with the weak plastic cap while adding some pop, and color to your engine bay. These Coolant caps retain ALL of the factory provisions by simply allowing you to snap the factory pressure-relief into the new Billet Cap We also designed these caps to complement our N5X Billet Oil caps, N5XBillet Oil filter housing caps, and Billet Power Steering cap and so all 4 will have the same design. We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize, as well as a choice of custom anodize at a cost of $100 extra. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT N5X/S55/N2X Billet BMW Oil Filter housing Cap
$89.99 – $199.99Price range: $89.99 through $199.99VTT is proud to offer our billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap, and the need for a special tool for removal, while adding some pop, and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. We also designed these caps to complement our Billet Oil caps, and upcoming Billet Power Steering caps, so all 3 will have the same design. Order all 3 - Oil Cap, Oil Filter housing Cap, and Power steering cap for $175 - 10% savings We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize, as well as a choice of custom anodize at a cost of $100 extra. The cap has a 19mm hex for easy installation, and removal, and includes a new sealing O-ring, and a small O-ring for the oil filter cage. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT M14/M12 Titanium Wheel Stud kits
$169.99 – $339.99Price range: $169.99 through $339.99VTT is proud to offer Titanium wheel stud kits for the owner looking for the lowest possible unsprung weight while maintaining high strength, and good looks as all come with an amazing burnt finish. This kit is 60% lighter than factory steel studs and nuts with a total kit of 20 nuts, and studs being 3.1LBS. Sets of 10 are 1.55 lbs -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Billet Check Valves
$27.99 – $31.99Price range: $27.99 through $31.99VTT CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Billet N54/N55 Vacuum/Boost Adapter
$53.99 – $69.99Price range: $53.99 through $69.99We are happy to release our BMW B54/N55 (Limited N55 Fitment) vacuum/boost adapter. These go inline with the Throttle Body fitting and provide a full boost/vacuum signal from the manifold. This fitting adds two 1/8NPT bungs to accept any fitting that has 1/8" NPT threads. You can choose options, 1/4" barb, as well as 1/8NPT plugs if you only want one barb, etc. These are perfect for running your PI off manifold pressure which is much more accurate than charge pipe, and they are also great for BOV running the proper size line without having to drill a hole in your manifold. These do space out any sensors etc giving inaccurate readings like some of the other brands do. They are made from 6061-T6 anodized black, with steel plugs, and Blue Anodized barbed fittings. You can choose to order in a few ways. You can choose straight or 90-degree barbs. Adapter alone - $40 Basic kit - 1 Adapter, 1 barb, and one plug, one vacuum cap, and one zip tie $45.00 Dual Barb kit - 1 Adapter, 2 barbs, one vacuum cap, and one zip tie $55.00 -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT N5X/M5X/N2X Billet Power Steering Cap
$79.99 – $189.99Price range: $79.99 through $189.99VTT is proud to offer our billet replacement for the factory plastic Power steering cap. This cap does away with the weak plastic cap, while adding some pop, and color to your engine bay. These Power Steering caps retain ALL of the factory provisions including dipstick, and vent hole We also designed these caps to complement our N5X Billet Oil caps, and N5XBillet Oil filter Caps caps, so all 3 will have the same design. Order all 3 - Oil Cap, Oil Filter housing Cap, and Power steering cap for $175 We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize, as well as a choice of custom anodize at a cost of $100 extra. -
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsDo you work on BMW engines across multiple platforms? Tired of modifying universal engine stand plates just to make them fit? Frustrated by losing access to the flywheel side once the engine is mounted?
We were tooāso we built the solution.
The VTT BMW Engine Stand Plate is a true bolt-on design that keeps the flywheel end fully accessible while providing a strong, stable mounting solution for your engine builds.
Machined from solid 6061-T6 billet aluminum and anodized in five colors for long-term durability and corrosion resistance, these plates are lightweight yet rated for over 1200 lbs.
Fitment: N54, N55, S55, B58, S58 (more coming soon)
- Note: The stand tube is 60mm or 2.36ā OD, which fits most engine stands, but not allāplease measure before purchasing.
Key Features:
- Lightweight, high-strength billet 6061-T6 construction
- Durable anodized finish
- Direct bolt-on to intake-side motor mount location
- Full clearance for accessories and flywheel/flex plate access
- Built-in provisions for locator pin and rotation bar
-
Quick ViewLooking for a little extra clearance on your coolant tank fitting due to relocation for single turbo, forward-facing intake manifold, etc. This 90-degree fitting will allow you to run the hose straight down instead of straight out, and increase your clearance, and routing choices. Made of 6061-T6 and anodized black for a long-lasting finish. Comes with fitting, and 1 clamp.
-
Quick ViewThis is an easy way to order all 3 VTT Billet engine caps for Valve Cover, Power steering, and Oil Filter Cap. We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize, as well as a choice of custom anodize at a cost of $399 total for custom
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT N54, N55, S55, N20, B58 Billet Motor Mount Inserts
$179.99 – $474.99Price range: $179.99 through $474.99 -
Quick ViewAre you building a single kit for the N54, N55, or S55 platform? The stock studs are usually a little bit short for most single-head flanges, and finding M7 studs is not easy. So we made our own longer studs to combat the issue. Made from 10.9 grade steel, and coated in black oxide, these are the perfect solution to the short stud problem. Sold individually so order the number you need. Stud details are as follows
- Overall length 47mm (stock 39mm)
- 3mm shoulder
- 6mm head which is 5mm hex
- 14mm short end
- 24mm long end (stock 15mm)
Dont forget our M7 copper lock nuts as well to complete the job - https://vargasturbo.com/product/vtt-fab-m7-copper-locking-exhaust-nuts/
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT- S55 / N55 PCV Delete kit
$99.99 – $399.99Price range: $99.99 through $399.99Have a problematic PCV on your S55/N55 powered BMW, don't want to pay to replace the entire VC? The VTT PCV delete kit is just what you need. This kit blocks the factory PCV from pulling from the head ports, gets rid of the tear-prone rubber diaphragm, and essentially converts your VC into VTA through the factory front port on the VC. This kit can work stand-alone with the cap, and a -10 ORB plug, can be used to run an extra breather port, or it can be installed with any Catch Can kit that uses the front port of the stock VC. Simply remove the factory cap, take out the diaphragm, screw the plug into the center port, and tap the new cap on with a soft blow hammer or similar. This deletes the PCV and allows you to avoid the issues of a failed diaphragm. Kit Choices- Cap and -10ORBĀ plug only (to be used with an existing catch can or VTA)
- Cap and Catch can kit (recirc or VTA) Complete kit to delete the PCV, and run a catch can (Currently works with S55 only)
- Cap Only (To be used if routing an additional hose from the cap to location or set up of choice, requires your parts to work)
- 1 PCV Cap
- 1 PCV port block off Plug
- 1 -10 ORB Plug
- Optional Catch Can kit
-
Quick View
N55 Stage 1 JB Upgrade Kit (NEW)
From: $1,244.98WHP Level supported (with proper fuel, upgrades, and tuning) Stock ā 425WHP -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT VAG/BMW/TOYOTA Billet Wheel Spacers
$21.99 – $37.99Price range: $21.99 through $37.99VTT Billet Wheel Spacers
VTT is proud to offer billet wheel spacers for most VAG, BMW, and the A90/91 Toyota Supra platforms.
Each spacer is:
-
CNC-machined from 6061-T6 aluminum
-
Hard anodized black for a long, corrosion-free life
We offer multiple fitments and sizes to suit a wide range of applications.
THESE ARE SOLD INDIVIDUALLY, FOR ONE AXLE ORDER TWO FOR A COMPLETE SET ORDER FOUR.
ANYTHING OVER 5MM WILL REQUIRE LONGER BOLTS OR STUDS. YOU CAN CHOOSE TO ADD A VTT WHEEL STUD KIT FROM THE OPTIONS.
PLEASE DOUBLE CHECK YOUR BOLT PATTERN AND HUB BORE BEFORE YOU ORDER. INSTALLED SPACERS CANNOT BE RETURNED!
-
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewN55 Installation kit
$74.99 – $189.99Price range: $74.99 through $189.99 -
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVTT is proud to offer a Titanium hardware upgrade for all our Billet and Cast VC's. This will come with M6x30 Ti bolts N54 /N55/S55/B58 Gen 1/ B58 TU it will be an Umbrella head with a 16.3mm head. These bolts weigh half as much as comparable steel hardware and look amazing. Colors to choose from will be Burnt, Black, and Natural (silver) -
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe stock outlet adapter on the N54/55 is NOTORIOUS for cracking when removing. This Billet replacement ensures no leaks, and no more cracked adapters. Available in 6 colors! Black, Red, Clear, Blue, Purple, Gold -
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVTT is Proud to offer our Billet Aluminum DCT Transmission pan. This pan does away with the factory plastic pan and upgrades it to 6061-T6 aluminum anodized in a variety of colors. This pan increases fluid capacity by 80% or almost DOUBLE the stock pan, has a US-made reusable Viton Gasket, a rare earth magnet built in to pull metal from the fluid, machined external fins to help aid in cooling, and a -6 ORB drain plug. Product Features:- Billet constructionĀ using 6061-T6 aluminum for long life, and added strength
- 80% or Almost DOUBLE the factory fluid capacity at 2000ML compared to 1150ML
- Machined fins for improved cooling
- Rare Erath magnet built in to pull metal from the fluid
- US-Made Viton Gasket
- -6 ORB drain plug for easy service
-
Quick ViewGet rid of the restrictive stock plastic intake on your E-Series N55 powered BMW, and replace it with our 2.5 full flow aluminum intake. This is a MUST when upgrading turbos, or trying to get the most from your stock turbo. Constructed of high-grade aluminum, and powder coated with a very durable gloss black finish this upgrade looks as good as it performs.
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT-FAB Billet Mac Solenoid brackets
$49.99 – $53.99Price range: $49.99 through $53.99Building a kit using Mac solenoids to control boost? Need an easy way to mount it? VTT-FAB has you covered with our billet Mac Solenoid brackets. Machined from 6061 billet and anodized in 3 colors, these are the perfect way to mount your Mac valve and look good while doing it. Each kit includes:- One Mac Solenoid bracket (3-Port or 4-Port)
- 2 Allen screws to hold the valve to the bracket
- M6 Moutning Bolt
-
Quick ViewAre you building a single kit for the N54, N55, or S55 platform?Ā M7 Locking exhaust nuts is not easy. So we made our own to combat the issue. These are the perfect solution to the problem of hard-to-find M7 lock nuts. Sold individually so order the number you need.
Note:Ā This is nuts ONLY Stud not included, by our extended M7 studs here - https://vargasturbo.com/product/vtt-fab-extended-m7-n54-n55-s55-b58-2-port-head-studs/
-
Quick ViewLooking to make sure all metal contaminates that are possibly in your oil are not circulated? VTT has you covered with our Titanium Magnetic oil drain plugs for BMW, and any other vehicle that uses an M12x1.5 drain plug. This drain plug will capture any ferrous metal in your oil, and capture it to be cleaned during your next oil change. It also is stronger than a Steel or Aluminum drain plug, and looks cool! These are made from GR5 Titanium and use a rare earth magnet to capture metal particles in your oil... Kit includes:
- 1 Titanium Drain Plug
- 1 M12 Crush Washer
-
Quick ViewLooking to remove the HPFP or DI system on your N54? this plate will block the vacuum pump and prevent oil leaks. You will need to remove any fuel lines, etc. Kit includes
- Block Plate
- 3 bolts
- O-Ring
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / Details -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Carbon Fiber Dragy Holder
$21.99 – $51.99Price range: $21.99 through $51.99Tired of your Dragy flying all over the car as you try to do runs? Tired of low sats or no sats warning due to improper location of the Dragy in the vehicle? Well say goodbye to those issues with our new Carbon Fiber and Plastic Dragy holders. These are made from either 100% Pre-Preg Carbon Fiber, or molded plastic for a perfect fit. The carbon fiber gives it just the right look to add to your performance vehicle! Each holder has dual Suction cups and will stick to any smooth surface. We suggest mounting them in the upper left or right corner of your windshield with a full view of the sky. Dragy holder features- Stop your Dragy from flying off the dash, and having to search for it
- Position your Dragy in the optimal position for the best satellite coverage
- VTT Dragy holder exposes the entire top of the Dragy so nothing is blocking the receiver from the Satellite
- The charging port is not blocked and can be accessed with the cover on
- Choose from REAL Carbon Fiber or Molded Plastic
-
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewN55 VR9 TurboSmart KOMPACT EM DV
$230.37 – $270.74Price range: $230.37 through $270.74VTT Is proud to offer the Turbosmart Kompact EM DV for the N55 The award-winning Kompact EM series Diverter Valves, are the worldās first truly plug and play Diverter Valves. Simply unplug and unbolt your OEM Diverter Valve, and install ours in its place. No adapters, hoses, or extra assembly required. All this while retaining complete OE control of the DVās operation. -
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT BMW Carbon Fiber Driveshaft
$1,699.99 – $1,878.49Price range: $1,699.99 through $1,878.49VTT Carbon Fiber Driveshaft for BMW Applications
Why overpay for a carbon fiber BMW driveshaft?
VTT is proud to offer a premium carbon fiber driveshaft manufactured exclusively for VTT in the USA by GCDS (Gulf Coast Driveshaft) ā one of the premier driveshaft manufacturers in the country with extensive experience in high-performance and drag racing applications.
Each driveshaft is constructed using 3.31" carbon fiber tubing, paired with NEAPCO Performance 1350 series U-joints, then bonded using a proprietary high-strength process and precision balanced to within 1/8 in-oz as a complete assembly.
Every shaft is torque tested in-house prior to shipping to ensure proper bonding and structural integrity. GCDS and VTT are among the few manufacturers that perform full torque testing on each shaft before it leaves the facility.
To complete the system, the driveshaft is paired with VTT-designed 7075 aluminum adapters, eliminating the factory guibos and unnecessary flex points. The shaft connects directly to the BMW 3-bolt front flange, while a VTT 4340 rear adapter replaces the factory slip-in / screw-retained shaft design for improved strength and reliability.
Proudly Made in the USA.
PLEASE NOTE! YOU MUST SEND US YOUR VIN NUMBER TO PROPERLY PROCESS YOUR ORDER, IF YOU DO NOT SEND YOUR VIN, YOU ORDER IS GOING TO BE HELD
PLEASE NOTE! Driveshafts can have UNUSUALLY LONG LEAD TIMES. We hope to reduce this with GCDS, but if the shaft shows OUT OF STOCK, expect a lead time of 4ā8 weeks, unless we specifically state that it can ship sooner.
Due to the nature of these shafts being manufactured by a 3rd party, ANY ORDERS PLACED FOR VTT CF DRIVESHAFTS ARE 100% FINAL.
NO REFUNDS. NO CANCELLATIONS. FOR ANY REASON.
THIS INCLUDES LONG LEAD TIMES.
PLEASE ORDER CAREFULLY. ONCE THE ORDER IS PLACED, IT IS FINAL.
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT N54/55 BMW Single Piece Silicone Cold Side Charge Pipe
$112.49 – $464.99Price range: $112.49 through $464.99VTT is proud to offer the very best charge pipe solution for the BMW E Series N54/55 platforms. This system completely does away with the restrictive, and muli-connection stock charge pipe system, and replaces it with a single 6-ply, Heat Resistant, Wire reinforced silicone charge pipe rated at over 200 psi.FITMENT:
ā¢ E Series N54 vehicles 335, 135 (Does not fit Z4, and 5 Series) ā¢E Series N55 vehicles 335, 135 (Does not fit SUV or other models) -
Quick View
VTT “GC” S55/N55 to B58 Coil Conversion Kit
From: $339.99VTT is proud to offer its very own Game Changer S55/N55 to B58 Coil conversion kit for the BMW S55/N55 platforms. The 55 series of engines has notoriously had ignition problems with the factory coils, while aftermarket upgrades do exist, they can be bulky. The solution is the BMW B58 ignition coils which are extremely robust and can support well over 1000WHP with no issues. This means a plug-and-play affordable solution that fits like stock, and looks AMAZING doing so! We designed our own 6061-T6 Billet bracket in a plethora of colors including matching shades for every S55/N55 Valve Cover. This means you can mix and match the color of the bracket with coil color, with VC color to truly tailor your engine bay to look exactly how you want it to!Note: Flash setting changes may be required when installing the conversion kit to ensure the proper function of the B58 coils with S55/N55 DME. This can be found in almost all flashing software settings such as MHD, Bm3, etc.
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewReplacement Gasket for VTT Valve Covers
$31.99 – $69.99Price range: $31.99 through $69.99Need to replace the gasket on your VTT Aluminum VC? Simply choose your model from the dropdowns to ensure you get the correct version. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Billet Crankcase Breather replacement filter
$21.99 – $27.99Price range: $21.99 through $27.99Need a replacement filter for your VTT Billet Crankcase breather? You can order on here. We offer them in 3 heights, low 48mm, medium58mm, and tall 68mm. This is measured from base to top. The filter will include a new clamp. For reference: N54/55 mostly use the low A90 Supra use Medium Most Audi applications can fit a tall, but measure your filter before ordering. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT “Spline Lock” Hub Puller
$74.99 -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT BMW M12x1.50 Wheel Stud Kits
$74.99 – $137.49Price range: $74.99 through $137.49Looking to get rid of your factory wheel lugs, and convert them to a high-quality stud kit for track purposes or just to make wheel changes easier? We got covered with our VTT wheel stud conversion kits. These kits are forged cold-rolled steel in 10.9 class, with corrosion-resistant coating for years of use. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT S55/N55 EWG BILLET CNC Valve Cover
$1,519.99VTT S55/N55 EWG Billet Aluminum Valve Cover
Performance. Durability. Style. VTT is proud to introduce our S55/N55 EWG Billet Aluminum Valve Cover, built for owners who want to upgrade both form and function. Whether you're looking to replace your aging plastic OEM valve cover or you're running a single turbo conversion and need better clearance and heat resistance, this cover delivers on all fronts. Designed to eliminate the problematic factory PCV system, our cover allows you to configure your PCV setup exactly how you want it. We strongly recommend pairing it with a catch can for optimal performance. Each unit is fully baffled to reduce oil carryover and ensure clean crankcase ventilation.
š ļø Valve Cover Features:
- ā 100% CNC-Machined from 6061-T6 Billet Aluminum
- ā Anodized Finish in a variety of colors for a clean, custom look
- ā Lightweight Design: 9.7 lbs (vs. 7.9 lbs stock ā only 1.8 lb difference)
- ā Fully Modular PCV Configuration ā run it your way
- ā Fully Baffled Ports to prevent oil escape
- ā A must-have for single turbo conversions ā better clearance and superior heat resistance
- ā Durable & Reliable ā a major upgrade from the OEM plastic cover
š¦ Kit Includes:
- (1) Billet Aluminum Valve Cover
- (1) Set of All Required Hardware
- (1) U.S.-Made Viton Gasket
ā ļø Important Installation & PCV Notes:
When upgrading to an aluminum valve cover, you are removing the factory PCV system and its integrated functionality. If you do not replace it with an external PCV setup, your S55 may smoke or bypass oil under boost or idle conditions. We highly recommend the following:- ā At a minimum, install an external low-side PCV to ensure vacuum at idle, which aids in turbo oil drainage
- ā Block off the head ports to relieve pressure on the valve cover gasket and prevent boost leaks into the crankcase
- ā Pair this valve cover with our Modular Catch Can Kits and Head Port Block-Off Kits for the best results
Upgrade your S55 or N55 with confidenceāditch the plastic, control your PCV, and enhance your engine bay with the VTT Billet Valve Cover. -
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT 15″/17″ Drag Pack Wheels for BMW/Toyota/VAG
$256.49 – $341.99Price range: $256.49 through $341.99Looking for a Lightweight, AFFORDABLE drag pack that looks amazing for your BMW, Toyota, or VAG platform? Look no further! VTT is proud to announce our lineup of Drag pack wheels for various BMW/Toyota/VAG fitments! We teamed up with Rota and had them open custom molds for us of their extremely popular Grid design. With these molds, we have an exclusive on 15X10, 17X10, and 17X4.5 wheels in our exact specs. The wheels are currently offered in the colors and sizes belowA variety of Offsets are available, as well as spacers here - VTT Spacers can be found here - https://vargasturbo.com/product/vtt-billet-wheel-spacers/
As well as Center bore adapters here -Ā https://vargasturbo.com/product/vtt-billet-hubcentric-wheel-bore-adapters/Wheels are priced EACH, meaning per wheel
PLEASE NOTE! CHECK FITMENT CAREFULLY. ANY WHEELS THAT HAVE HAD TIRES MOUNTED OR ARE DAMAGED DURING TEST FITTING ETC. ARE NOT RETURNABLE!
We make NO CLAIM these fit ANY PLATFORM, or ANY factory brake set up. It is YOUR JOB to measure, and make sure they will fit BEFORE you mount tires or install them. WE NEVER suggest shaving down brake calipers to fit a smaller wheel. If they do not fit. GET A SMALL BRAKE KIT!
Colors offered:- Satin Black
- Gloss Black
- Bronze,
- Gun Metallic
- 15x10 ET45/ET40 (wheel weight 16 lbs)
- 17x10 ET45/ET40/ET25 (wheel weight 19lbs)
- 17x4.5 ET-20 (wheel weight 16 lbs)
- 15x10 ET45 - (wheel weight 16 lbs)
- 17x10 ET45/ET40/ET25 (wheel weight 19 lbs)
- 17x4.5 ET-20 (wheel weight 16 lbs)
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT N55 GC/GC+ Turbocharger Upgrade
$2,769.99 – $3,089.99Price range: $2,769.99 through $3,089.99Supported power level: GC Stock-600WHP GC+ Stock-700 WHP Ready to take your N55 to the next level?Ā Donāt want to deal with core charges, long lead times, or restrictive factory housings? Look no further! VTT has you covered with our 100% new casting N55 āGCā andĀ āGC+ā turbocharger upgrade. We start by keeping the great design elements of the factory N55 turbo and removing the not-so-great ones such as the small factory inlet area, bearing housing oil structure, thrust bearing, and anything else we saw that could be improved upon.Ā With the basics covered, we stepped it up a level adding proprietary VTT changes, and finished off by having all these parts cast to OE quality.Ā What this means for you is serious N55 power made easy; GCs are a drop in turbocharger upgrade that supports over 600-700 WHP while maintaining factory like spool and all factory connections including oil, water, downpipe, and charge pipe. -
Quick ViewVTT is proud to offer a truly plug-and-play line lock kit for select BMW vehicles that does NOT require running wiring inside the car, mounted switches, holes in the dash, etc. Our newly designed and released line lock kits use a 40amp wireless remote control switch with 4 different modes that allow you to tailor your line lock setup exactly as you prefer. You simply install the solenoids, install the harness with the switch which has all the wiring terminated, bleed the brakes, and you are ready for effortless burnouts which will not be interfered with by the DME because you are holding the brakes, nor wear your rear brake pads. You can store the remote anywhere in your vehicle, center console, cup holder, door cup holder, etc., and when you need to do a burnout to heat your race tires it's in arm's reach without running any wiring into the vehicle. Fitment is confirmed for G8X M3/4, A9X Supra - The kit itself including lines, solenoids, etc will fit most all late model BMW Chassis including F8X, F3X, G2X, etc. The main concern will be mounting the wireless switch in the passenger cowl area. The kit includes:
- Line lock solenoids with weather pack connectors
- Two Parker 90-degree -3 an fittings
- Two Stainless Steel adapter fittings
- Two DOT Approved Stainless Steel brake lines
- One complete wiring harness
- One Remote control switch with TWO remotes
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsWe have heard all the stories about fluid all over the engine bay, seen the headbands, socks, sweatbands, and all the fixes people have used and still have issues with their PS reservoir.Ā So we decided to do something about it, and started with a ground-up design that completely fixed all those issues, and added some much-needed features to an old BMW design. Kit Includes:- 1 PS Reservoir in choice of color
- 2 or 4 fittings
- 2 Hose clamps
- Optional One-Way Breather
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLooking to adapt your wheel bore size to a smaller hub bore? VTT has you covered with our hub-centric adapters. These adapters are made from Billet 6061-T6 aluminum, and anodized in black. We have these sizes currently- 57.1mm hub to 60.1mm wheel bore
- 57.1mm hub to 64.1mm wheel bore
- 57.1mm hub to 66.1mm wheel bore
- 57.1mm hub to 66.6mm wheel bore
- 57.1mm hub to 67.1mm wheel bore
- 57.1mm hub to 70.3mm wheel bore
- 57.1mm hub to 71.6mm wheel bore
- 57.1mm hub to 72.6mm wheel bore
- 57.1mm hub to 73mm wheel bore
- 57.1mm hub to 74mm wheel bore
- 57.1mm hub to 74.1mm wheel bore
- 64.1mm hub to 72.6mm wheel bore
- 66.6mm hub to 72.6mm wheel bore
They are sold in sets of two, order TWO SETS for a full car, or one set per axle.
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Mini Billet Check Valves
$5.99 – $11.99Price range: $5.99 through $11.99 -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT-FAB Extension Harnesses
$49.99 – $104.99Price range: $49.99 through $104.99Need to move your coolant expansion tank to the other side of the vehicle for a single turbo kit you are building, extend Map sensor plugs, or IAT, how about Throttle Body? Don't cut your factory wires. Just get a VTT-FAB extension harness, and plug and play! These come in various lengths and are covered in expanded sheathing with heat shrink on both ends for a long-lasting, good-looking finish. Available:- Coolant Extension for late model BMW 2015+ 5 ft
- Pre-Throttle Map sensor extension harness 2 ft
- Pre-Throttle IAT Sensor extension harness 2 ft
- B58/S58/B48 etc Throttle body extension harness 2 ft
- B58 to S55 Throttle conversion/extension harness 2 ft
- EWG Actuator Extension harness, Various Lengths
- N54 stock MAP to N20 Map sensor extension
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVTT S55/N55 EWG Cast Aluminum Valve Cover
VTT is proud to introduce our S55/N55 EWG Cast Aluminum Valve Cover, designed for performance-driven BMW owners looking for a durable, stylish, and functional upgrade. This option provides a cost-effective alternative to our billet valve cover while still delivering enhanced engine bay aesthetics and eliminating the failure-prone factory plastic cover, which can crack over time.
Beyond durability, this valve cover removes the problematic factory PCV system, giving you complete control over how you set up your PCV. We highly recommend pairing it with a catch can for optimal performance. Additionally, this cover is perfect for single turbo conversions, offering increased clearance and improved heat resistance.
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Billet BMW N54/N55/S55/B58 “HEAD HANDLER” Cylinder head lifting tool
$69.99 – $89.99Price range: $69.99 through $89.99Do you work on a lot of BMW engines from various platforms? Do you ever struggle with heavy cylinder heads, either lifting off the engine or simply moving around? Ever ruined an EXPENSIVE multi-layer head gasket while trying to install a cylinder head due to no secure way to hold it without two people. We answered yes to all of those things, and came up with a tool for anyone that works on BMWs often, and needs a way to simply, and easily remove/install, or simply move around a cylinder head. These cylinder head tools are machined from a solid billet of 6061-T6 aluminum and anodized in 4 colors for long-lasting corrosion resistance. They are knurled for non-slip grip when oily or wet, and positioned so the head is balanced when lifting The Head Handler fits the following engines, N54, N55, S55, B58 and we offer short extensions for installation with no cams/Cam ledges on the head, or long extensions for people that want to install or remove a head with cams still installed. (B58 only requires short extensions) -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewCNC N54/N55 Single Flange
$329.99 – $409.99Price range: $329.99 through $409.99100% CNC flange in mild or SS. This flange will fit all N54's and N55's and comes COMPLETE ready for welding your runners onto it -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT BMW Plug and Play Pre AND Post throttle 5-Bar (58 psi), 6-Bar(72 psi) Map Sensor Kits
$177.49 – $209.99Price range: $177.49 through $209.99Looking to up your boost limit on just about any BMW vehicle that runs a 3 or 4-wire BMW map sensor including but not limited to S58, B58, N54, N55, S55, S63, B48, B47, B42, B57, B46? We were too, so we decided to make a very easy plug-and-play kit for 3, and 4-wire BMW map sensors. These kits will allow you to completely replace the 3-wire sensor with one of our sensors, leave your stock 4-wire in place for IAT sensing, and move the power, ground, and sensor signal from the factory sensor to our sensor. These sensors have the proper scaling which will allow your tuner to simply change your map sensor scaling in the tune, and the factory ECU will be able to utilize the sensor voltage with no problem. We are offering these in 5 bar (58 psi), and 6 bar (72 psi), and each comes with a plug-and-play harness, and optional fittings for ease of installation.Note: For the S58/B58 our Factory style Pre-Throttle map sensor is also 5 bar, and will work fine coupled with the post throttle kit, but the scaling is different, if you want matching Voltages Pre/Post throttle you can run two of these.
A variety of install pics can be found below and - Here
Scaling PDF Links: 5-Bar / 6-Bar
Features include:- Plug and Play harnesses with no wire splicing
- Output wire for connecting a PI or external controller to your post-throttle map sensor for the most stable signal that is not affected by throttle closure
- Different fittings are available for your plumbing needs.
- Can have matching voltage signals for pre/post throttle for ease of tuning, and boost reference
- B58/S58 etc Pre Throttle - 3 Wire Harness (Charge pipe to 1/8" NPT adapter needed, for B58/S58 90 degree adapter needed to provide sensor clearance)
- B58/S58 Post Throttle - 4 Wire Harness (Boost reference will be needed from manifold to sensor)
- F90 M5 Pre/PostĀ Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- Most all other platforms Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- B58
- S58
- S63/ S63TU
- N63
- N54
- S55
- N55
- N20
- B46
- B48
- B57
- B47
-
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT-FAB Billet Velocity Stack
$35.69 – $45.89Price range: $35.69 through $45.89Running an open turbo, and want to straight out the airflow to the compressor for extra efficiency. Our billet velocity stack is what you need. Backed by physics a Bellmouth or velocity stack will help smooth the air coming into the turbocharger or on NA cars. These are made from 6061-T6, and anodized in a variety of colors and sizes. Currently, we offer 3", 4", and 5" These are suitable to fit any intake tubing or turbocharger inlet with that size. These are available with or without a silicone connector and clamps. Our V-Stacks are also made to extend down on the outside so you can attach a Vibrant S&B or other compatible 7" Filter on the 3"/4" version. Features:- Smooth air before it enters the turbocharger or Intake
- Very low profile, only sticking 2.5" above the turbocharger inlet. Even if you have no room for a filter these will fit
- Fits all turbochargers with a 3", 4" or 5" inlet including PTE Sportsman Cover!
- 3" and 4" version works with Vibrant #10961 7" filter or S&B 1032 FilterĀ if you have room
- 100% billet construction for high-strength
- Anodized for long life, and durability
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Brake Kits Rotors/Hats only
$117.49 – $262.49Price range: $117.49 through $262.49This is for those running our brake kits that use our 11.75" or 13" Rotors that want to easily change between rotors for dedicated drag racing and street use. You can now buy Rotor/Hat Assemblies by themselves to switch between any of our 3 optionsThe price is for ONE ROTOR / OR ONE ROTOR/HAT ASSEMBLY
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT E/F Series BMW Ultimate Front Drag Brake Kit
$1,399.99 – $1,949.99Price range: $1,399.99 through $1,949.99Looking to make your E/F Series BMW faster in the 1/4 mile or 1/2 mile racing? Want to run 17" or 15" wheels in the front? Want to drop OVER 54lbs of unsprung weight off the front of the car at the same time? Do not want to break the bank while doing so? Look no further than the VTT Ultimate Front Drag kit for the E/F Series BMWs. This kit will allow you to run the wheel/tire combo you need to drop your ETs all while putting the car on a significant diet over the stock front brake setup. The kit is a true plug-and-play kit using Genuine VTT parts, coupled with DOT-approved brake lines, CNC 7075 rotor hats/brackets, and a CEL eliminator harness for the brake sensor. This kit comes in 1 variation, with two different caliper Options for each. We HIGHLY suggest 6-piston Calipers for street driving and 1/2 mile racing. These calipers will drop weight, AND be a braking upgrade over stock calipers. -
Sale!Quick View
PFS Bucketless Double Shot Fuel Pump Upgrade
$649.99Original price was: $649.99.$552.49Current price is: $552.49.
Product categories
- 10% Max Discount
- 15% Max Discount
- BMW
- Diesel
- Dodge V8 Platforms
- Ford
- Honda
- Hurricane I6
- Mercedes
- Mitsubishi
- N/S63TU
- No Discount Products
- Porsche
- Powersports
- Tier OBD
- Toyota
- Uncategorized
- Universal
- VTT
- VTT-FAB
- VTTEV
- VW/VAG