-
Quick ViewLooking to go above 45 psi in your BMW-powered vehicle? Looking for a plug-and-play solution? We have you covered with our BMW 5 bar sensor. These will allow 58 psi to be read and are factory plug-and-play. Simply remove your old sensor, replace it with the 5 bar, and have your tuner rescale your map values in both your DME tune and your PI tune if applicable.
These are GENUINE BMW sensors directly from BMW.
PLEASE NOTE: These are GENUINE BMW sensors directly from THE BMW DEALERSHIP, BMW IS PUTTING A BMW STICKER OVER A DENSO BOX, AND SELLING THEM. THESE DO NOT HAVE BMW STAMPS ON THEM. WE HAVE ZERO CONTROL OVER THIS.
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVTT is proud to offer high-performance drop-in replacement filters for the 2021+ G8X M3/M4. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. On the dyno, we saw more than 13WHP gains with these filters and our Carbon Fiber intake Tops. These filters will also work perfectly with the stock tops. We recommend removing the pre-filter for best flow if the stock top is used. We offer them in two colors. Red, and Black
Features:- 50 States Emissions Legal
- Easy to install 15-30 minutes even for a novice
- Filters can be cleaned forever meaning never buy new filters
- Up to 13WHP gains
- Completely reversible if you ever want to remove
Fitment: 2021+ BMW
- G80 M3
- G82 M4
- G83 M4 Convertible
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT BMW Plug and Play Pre AND Post throttle 5-Bar (58 psi), 6-Bar(72 psi) Map Sensor Kits
$177.49 – $209.99Price range: $177.49 through $209.99Looking to up your boost limit on just about any BMW vehicle that runs a 3 or 4-wire BMW map sensor including but not limited to S58, B58, N54, N55, S55, S63, B48, B47, B42, B57, B46? We were too, so we decided to make a very easy plug-and-play kit for 3, and 4-wire BMW map sensors. These kits will allow you to completely replace the 3-wire sensor with one of our sensors, leave your stock 4-wire in place for IAT sensing, and move the power, ground, and sensor signal from the factory sensor to our sensor. These sensors have the proper scaling which will allow your tuner to simply change your map sensor scaling in the tune, and the factory ECU will be able to utilize the sensor voltage with no problem. We are offering these in 5 bar (58 psi), and 6 bar (72 psi), and each comes with a plug-and-play harness, and optional fittings for ease of installation.Note: For the S58/B58 our Factory style Pre-Throttle map sensor is also 5 bar, and will work fine coupled with the post throttle kit, but the scaling is different, if you want matching Voltages Pre/Post throttle you can run two of these.
A variety of install pics can be found below and - Here
Scaling PDF Links: 5-Bar / 6-Bar
Features include:- Plug and Play harnesses with no wire splicing
- Output wire for connecting a PI or external controller to your post-throttle map sensor for the most stable signal that is not affected by throttle closure
- Different fittings are available for your plumbing needs.
- Can have matching voltage signals for pre/post throttle for ease of tuning, and boost reference
- B58/S58 etc Pre Throttle - 3 Wire Harness (Charge pipe to 1/8" NPT adapter needed, for B58/S58 90 degree adapter needed to provide sensor clearance)
- B58/S58 Post Throttle - 4 Wire Harness (Boost reference will be needed from manifold to sensor)
- F90 M5 Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- Most all other platforms Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- B58
- S58
- S63/ S63TU
- N63
- N54
- S55
- N55
- N20
- B46
- B48
- B57
- B47
-
Quick ViewHeat is the enemy of power, and the last thing you want is hot coolant heating your charge air even further right before it enters the charge cooler, but this is what BMW has done on the S58. This is done for emissions and quick warm-up purposes. However, If you are looking to make power on the S58, and are upgrading your charge cooler, or adding PI. While you are there, it takes 30 seconds to remove the coolant lines from the TB connections and replace them with our billet coolant delete kit. This completely removes the coolant from the Throttle body and provides a bypass for the coolant. Simply remove the two lines going to the throttle body, and run our hose in their place. You leave the coolant fittings on the TB open and avoid any unwanted heat being introduced into your charge tract. In our opinion a must for full effort builds. We take the work out of it for you. Kit included:
- One Plug and Play TB Coolant Delete Hose
- Billet 6061 Anodized coolant fittings for long leak-free life
- Reinforced 7-ply silicone hose for strength and longevity
- Vibration-resistant crimp clamps
- 100% plug and play, NO cutting or removing factory clamps or hoses. Fully reversible
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsRunning upgraded stock frame turbos on your S58 powered G8X M3/4 or just looking to maximize airflow on stock turbos? We have you covered with our silicone intake tubes. These completely great rid of every restriction, accordion section, and any other issues designed into the factory pipes, and replaces them with 100% smooth-flowing silicon intake tubes. These are 7 layers, and wire is impregnated to ensure they will never collapse even under extreme vacuum. Design Features:- Smooth bends, and increased area for maximum flow no matter what turbos you are running
- Wire impregnated 7-Layer Silicone for high strength
- Billet anodized connectors for a great look and long-lasting finish
- High-quality German Clamps
- Easy install 30-45 minutes even for a novice
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVTT is proud to announce the first of our upcoming carbon fiber product line. The BMW S58 G8X M3/4 Carbon fiber intakes! BMW did a wonderful job designing these intakes and we have found they are only slightly restrictive at elevated power levels, mostly due to the secondary filter inside, and the factory paper filter. Beware of companies selling expensive intake systems, or cone set up, with a single dyno comparison claiming big gains. The factory setup is EXTREMELY efficient with only a couple of small changes. With this in mind, we decided to just take their cues, and make factory-style carbon fiber intake tops with no secondary filters, and high flow cotton pre-oiled filters. These are 8 layers of 100% carbon not a single layer wrapped over plastic and they are 1.3MM thick with our logo vacuum printed onto the tops, with a UV resistant gloss clear coating. This is not only strong but will resist discoloration for an extended period of time. The filters themselves are made with a heat-resistant silicone base, a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow.
Filters are available by themselves for a flow upgrade while keeping the stock look here - https://vargasturbo.com/product/vtt-2021-bmw-m3-m4-high-performance-drop-in-air-filter-upgrade/ Features:- 50 States Emissions Legal
- Easy to install 15-30 minutes even for a novice
- Beautiful Carbon Fiber finish really adds class to the S58 engine bay
- Filters can be cleaned forever meaning never buy new filters
- Up to 13WHP gains
- Completely reversible if you ever want to remove
Fitment: 2021+ BMW
- G80 M3
- G82 M4
- G83 M4 Convertible
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsNeed a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT “Game Changer” S58 Charge Air Cooler
$3,779.99 – $4,319.99Price range: $3,779.99 through $4,319.99VTT is proud to announce our “Game Changer” charge air cooler for the S58 G8X, and F9X X3/4M platforms! We have completed testing, and any production changes, and are happy to open Pre-orders for the coolers! While the factory charge air cooler is well done, and robust it leaves a lot to be desired on repeated pulls and ends up heat soaked very quickly. Using Proprietary US MADE “WAGNER Intercooler” Cores. We then couple that with CFD-designed runners, and end tanks that we have TIG welded right here in San Leandro California. With this strategy, we are able to take the limited space given to us by the factory, and add not only a larger more efficient core, but also much better designed/flowing runners, and end tanks. We also pack the unit with tons of awesome features, all at a great price! Pricing is as follows:- DI Manifold only - Raw Aluminum - $3999
- PI Manifold with Fuel Rail and PI provisions - Raw Aluminum - $4199
- DI Manifold only - Cerakoted with thermal Dispersion OR custom color - $4369
- PI Manifold With Fuel Rail and PI provisions - Cerakoted with thermal Dispersion OR custom color - $4569
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Billet Non-Marring Double Ended AN wrenches
$12.99 – $149.99Price range: $12.99 through $149.99Secure Your AN Fittings the Right Way – Without the Damage
VTT now offers a complete line of precision Billet 6061-T6 Aluminum AN Wrenches, designed to grip without marring your fittings. Whether you're working with -3 or -20 AN sizes, we've got you covered.These wrenches are lightweight, durable, and anodized in 8 vibrant colors for a long-lasting finish and easy size identification.
Available Options:
-
Full Kit: Includes all sizes from -3 to -20
-
Common Size Kit: Includes -4, -6, -8, -10, and -12
-
Individual Wrenches: Purchase only the sizes you need
-
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVTT is proud to offer our Pre-Preg Hand Crafted Carbon Fiber engine covers for the S58 engine. These are plug-and-play and snap into the factory mounting studs using the factory rubber mounts. BMW did a fabulous job on the latest engine offerings, but the overuse of plastics leaves the engine bays looking cheap, and unfinished. These carbon fiber engine covers, as well as our carbon fiber strut bars, are the perfect addition for anyone looking to give their engine bay, a polished, and sharp look. Available in Gloss, and Matte finish for the G8X and X3/4M platformsPLEASE NOTE: MUST REUSE FACTORY EMBLEM
-
Quick ViewVTT is proud to offer high-performance drop-in replacement filters for the 2019+ F9X X3/4M. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. The factory filters have been proven to be restrictive, and you can improve power, and milage with this simple yet effective upgrade! Simply remove your engine cover, swap in the upgraded filters, and enjoy a better-flowing engine! We offer them in two colors. Red, and Black Features:
- 50 States Emissions Legal
- Easy to install in 15-30 minutes even for a novice
- Filters can be cleaned forever meaning never buy new filters
- Up to 13WHP gains
- Completely reversible if you ever want to remove
Fitment: 2019+ BMW
- F97 X3M
- G98 X4M
-
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Upgraded Silicone G8X (S58) coolant hose kit
$189.99 – $799.99Price range: $189.99 through $799.99VTT Upgraded Silicone G8X (S58) Coolant Hose Kit
Available in BLACK as of 3/12/26 with RED, BLUE, and ORANGE coming very soon!
Upgrade the Weak OEM Plastic Coolant Connectors on Your BMW S58
The issue with the factory S58 coolant system is not the rubber hoses themselves — it’s the OEM plastic quick-connect fittings. Over time, these plastic connectors can become weak, crack, or fail, especially in high-heat performance environments.
VTT offers an upgraded 6-ply silicone coolant hose kit for the BMW S58 platform, featuring CNC-machined billet aluminum connectors for improved durability, reliability, and long-term performance.
This kit is designed as a direct replacement for multiple factory coolant hoses and connector assemblies shown in the OEM BMW cooling system diagram.
Beyond improving reliability, these hoses also add a splash of color to your engine bay, giving the S58 a cleaner and more performance-focused appearance.
Order the complete kit for a savings of almost 15%!
Product categories
- 10% Max Discount
- 15% Max Discount
- BMW
- Diesel
- Dodge V8 Platforms
- Ford
- Honda
- Hurricane I6
- Mercedes
- Mitsubishi
- N/S63TU
- No Discount Products
- Porsche
- Powersports
- Tier OBD
- Toyota
- Uncategorized
- Universal
- VTT
- VTT-FAB
- VTTEV
- VW/VAG