-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVTT BMW Billet One Way Crankcase Breather VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, and remove crankcase pressure, all while adding a cool look to your engine bay. Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one-way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.This breather will fit MOST NOT ALL BMWs with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54, S85, S63, S63TU, N63. There are factors that may stop it from fitting your platform such as valve cover style etc.
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / Details -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Ignition Coil Kits
$169.99 – $222.49Price range: $169.99 through $222.49VTT is proud to offer ignition coil replacements for the N5X platforms, as well as B5X, and many VAG platforms. We started our quest for coils by contacting multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once we were satisfied with the testing, we had the best performing coils made to our colors and specs. We offer these coils as complete sets for the N54, B58/S58, and the VAG platforms in either 4, or 5 cylinders. We also offer upgraded plugs which are highly recommended to change when doing coil replacements These coils come in 3 colors, Red, Black, and Blue, and are not simply an aesthetic upgrade but match or exceed the factory secondary spark energy. The VAG coil, is extremely potent, and the tester was so impressed with it compared to the factory coil, he called it a "BEAST" of a coilNote: To extract maximum performance from VTT coils minor tune changes are required to optimize dwell periods. See recommended Dwell times below
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT BMW Billet Coolant Reservoir Cap
$79.99 – $189.99Price range: $79.99 through $189.99VTT is proud to offer our billet replacement for the factory plastic Coolant Reservoir cap. This cap does away with the weak plastic cap while adding some pop, and color to your engine bay. These Coolant caps retain ALL of the factory provisions by simply allowing you to snap the factory pressure-relief into the new Billet Cap We also designed these caps to complement our N5X Billet Oil caps, N5XBillet Oil filter housing caps, and Billet Power Steering cap and so all 4 will have the same design. We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize, as well as a choice of custom anodize at a cost of $100 extra. -
Quick ViewLooking to make sure all metal contaminates that are possibly in your oil are not circulated? VTT has you covered with our Titanium Magnetic oil drain plugs for BMW, and any other vehicle that uses an M12x1.5 drain plug. This drain plug will capture any ferrous metal in your oil, and capture it to be cleaned during your next oil change. It also is stronger than a Steel or Aluminum drain plug, and looks cool! These are made from GR5 Titanium and use a rare earth magnet to capture metal particles in your oil... Kit includes:
- 1 Titanium Drain Plug
- 1 M12 Crush Washer
-
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT BMW Carbon Fiber Driveshaft
$1,699.99 – $1,878.49Price range: $1,699.99 through $1,878.49VTT Carbon Fiber Driveshaft for BMW Applications
Why overpay for a carbon fiber BMW driveshaft?
VTT is proud to offer a premium carbon fiber driveshaft manufactured exclusively for VTT in the USA by GCDS (Gulf Coast Driveshaft) — one of the premier driveshaft manufacturers in the country with extensive experience in high-performance and drag racing applications.
Each driveshaft is constructed using 3.31" carbon fiber tubing, paired with NEAPCO Performance 1350 series U-joints, then bonded using a proprietary high-strength process and precision balanced to within 1/8 in-oz as a complete assembly.
Every shaft is torque tested in-house prior to shipping to ensure proper bonding and structural integrity. GCDS and VTT are among the few manufacturers that perform full torque testing on each shaft before it leaves the facility.
To complete the system, the driveshaft is paired with VTT-designed 7075 aluminum adapters, eliminating the factory guibos and unnecessary flex points. The shaft connects directly to the BMW 3-bolt front flange, while a VTT 4340 rear adapter replaces the factory slip-in / screw-retained shaft design for improved strength and reliability.
Proudly Made in the USA.
PLEASE NOTE! YOU MUST SEND US YOUR VIN NUMBER TO PROPERLY PROCESS YOUR ORDER, IF YOU DO NOT SEND YOUR VIN, YOU ORDER IS GOING TO BE HELD
PLEASE NOTE! Driveshafts can have UNUSUALLY LONG LEAD TIMES. We hope to reduce this with GCDS, but if the shaft shows OUT OF STOCK, expect a lead time of 4–8 weeks, unless we specifically state that it can ship sooner.
Due to the nature of these shafts being manufactured by a 3rd party, ANY ORDERS PLACED FOR VTT CF DRIVESHAFTS ARE 100% FINAL.
NO REFUNDS. NO CANCELLATIONS. FOR ANY REASON.
THIS INCLUDES LONG LEAD TIMES.
PLEASE ORDER CAREFULLY. ONCE THE ORDER IS PLACED, IT IS FINAL.
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Mini Billet Check Valves
$5.99 – $11.99Price range: $5.99 through $11.99 -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT-FAB Extension Harnesses
$49.99 – $104.99Price range: $49.99 through $104.99Need to move your coolant expansion tank to the other side of the vehicle for a single turbo kit you are building, extend Map sensor plugs, or IAT, how about Throttle Body? Don't cut your factory wires. Just get a VTT-FAB extension harness, and plug and play! These come in various lengths and are covered in expanded sheathing with heat shrink on both ends for a long-lasting, good-looking finish. Available:- Coolant Extension for late model BMW 2015+ 5 ft
- Pre-Throttle Map sensor extension harness 2 ft
- Pre-Throttle IAT Sensor extension harness 2 ft
- B58/S58/B48 etc Throttle body extension harness 2 ft
- B58 to S55 Throttle conversion/extension harness 2 ft
- EWG Actuator Extension harness, Various Lengths
- N54 stock MAP to N20 Map sensor extension
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT BMW Plug and Play Pre AND Post throttle 5-Bar (58 psi), 6-Bar(72 psi) Map Sensor Kits
$177.49 – $209.99Price range: $177.49 through $209.99Looking to up your boost limit on just about any BMW vehicle that runs a 3 or 4-wire BMW map sensor including but not limited to S58, B58, N54, N55, S55, S63, B48, B47, B42, B57, B46? We were too, so we decided to make a very easy plug-and-play kit for 3, and 4-wire BMW map sensors. These kits will allow you to completely replace the 3-wire sensor with one of our sensors, leave your stock 4-wire in place for IAT sensing, and move the power, ground, and sensor signal from the factory sensor to our sensor. These sensors have the proper scaling which will allow your tuner to simply change your map sensor scaling in the tune, and the factory ECU will be able to utilize the sensor voltage with no problem. We are offering these in 5 bar (58 psi), and 6 bar (72 psi), and each comes with a plug-and-play harness, and optional fittings for ease of installation.Note: For the S58/B58 our Factory style Pre-Throttle map sensor is also 5 bar, and will work fine coupled with the post throttle kit, but the scaling is different, if you want matching Voltages Pre/Post throttle you can run two of these.
A variety of install pics can be found below and - Here
Scaling PDF Links: 5-Bar / 6-Bar
Features include:- Plug and Play harnesses with no wire splicing
- Output wire for connecting a PI or external controller to your post-throttle map sensor for the most stable signal that is not affected by throttle closure
- Different fittings are available for your plumbing needs.
- Can have matching voltage signals for pre/post throttle for ease of tuning, and boost reference
- B58/S58 etc Pre Throttle - 3 Wire Harness (Charge pipe to 1/8" NPT adapter needed, for B58/S58 90 degree adapter needed to provide sensor clearance)
- B58/S58 Post Throttle - 4 Wire Harness (Boost reference will be needed from manifold to sensor)
- F90 M5 Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- Most all other platforms Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- B58
- S58
- S63/ S63TU
- N63
- N54
- S55
- N55
- N20
- B46
- B48
- B57
- B47
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT HIGH-FLOW -16 Catch Can System
$499.00 – $649.00Price range: $499.00 through $649.00VTT -16 Billet HIGH-FLOW Catch Can System
Maximum Venting for Maximum Power
VTT is proud to introduce our -16 Billet High-Flow Catch Can System — designed from the ground up for high-horsepower applications requiring serious crankcase ventilation. Whether you're pushing over 900WHP or beyond 2000WHP, this system delivers unmatched performance, reliability, and engine bay cleanliness.
Key Features:
-
Supports -16 AN lines (with optional -12 or -20 fittings)
- 20 Fluid OZ capacity
-
Engineered for big-power builds needing high crankcase pressure relief
-
Triple-stage filtration system to eliminate oil mist — even in the event of engine failure
-
Designed, tested, and proven to keep oil inside the catch can — not in your engine bay
Triple Filtration Technology:
-
Stage 1 - Stainless steel filter – captures 95% of oil mist on entry
-
Stage 2 - Perforated diffuser plate – further disperses and slows down airflow
-
Stage 3 - Final stainless mesh layer – scrubs out any remaining vapor before venting
This advanced system has been tested with over 200 PSI of pressure and more than half a quart of oil without releasing a trace of oil mist. As long as the catch can is properly serviced and not overfilled, even catastrophic engine failure won’t result in a mess under your hood.
Application-Specific Kits Available:
We offer plug-and-play kits for popular platforms, including:
-
G8X M2/M3/M4 (S58) SINGLE TURBO ONLY
-
F9X X3M/X4M SINGLE SINGLE TURBO ONLY
-
A9X Toyota Supra
Each kit includes everything needed for installation: catch can, vehicle-specific bracket, fittings, hoses, and optional drain. Again: Plug-and-play kits include ALL required parts. Bracket, fittings, line, etc. No additional fittings are required except the drain if wanted.
-
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Billet Non-Marring Double Ended AN wrenches
$12.99 – $149.99Price range: $12.99 through $149.99Secure Your AN Fittings the Right Way – Without the Damage
VTT now offers a complete line of precision Billet 6061-T6 Aluminum AN Wrenches, designed to grip without marring your fittings. Whether you're working with -3 or -20 AN sizes, we've got you covered.These wrenches are lightweight, durable, and anodized in 8 vibrant colors for a long-lasting finish and easy size identification.
Available Options:
-
Full Kit: Includes all sizes from -3 to -20
-
Common Size Kit: Includes -4, -6, -8, -10, and -12
-
Individual Wrenches: Purchase only the sizes you need
-
-
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT X PFS “EBS” External Brushless System – 2500HP Capable
$2,379.99 – $2,719.99Price range: $2,379.99 through $2,719.99VTT x PFS EBS (External Brushless System) Fuel System
VTT, in collaboration with Performance Fueling Solutions (PFS), is proud to introduce the PFS EBS — External Brushless System.
The EBS is a fully stand-alone, next-generation brushless fuel system available in both platform-specific and universal fitments. Built around state-of-the-art Protec brushless pump technology, this system is capable of supporting up to 2,500 HP on ethanol-based fuels — and even more on gasoline or ethanol blends.
With its compact 15" x 10" footprint and ultra-lightweight construction, the PFS EBS is engineered for performance without compromise. The complete system — including pumps, surge tank, FPR, controllers, and wiring harness — weighs in at under 10 lbs (dry), thanks to a carbon fiber mounting plate and carefully chosen lightweight materials.
EBS Bench Testing Video:
EBS Bench Test Video -
Quick View
Stop the Flex. Launch with Confidence.
Soft bushings are the enemy of hard launches and drivetrain longevity. The factory BMW transfer case bushings on the F9X M5/M8 platform are notoriously soft—exactly the opposite of what you want when you're putting serious power to the ground.
Sure, you could replace the entire bushing with a solid one, but that often requires lowering or removing the transfer case—not to mention the added NVH (noise, vibration, and harshness) that comes with it.
Our VTT transfer case bushing inserts offer a smarter solution: reduce bushing flex without sacrificing comfort. You keep smooth, quiet drivability around town and at idle—but when it’s time to launch, the transfer case stays planted.
-
Quick ViewShow off your VTT support and get a good laugh from people with our "We Like To Party" License plate bracket. Born from the infamous quote in Talladega nights
Product categories
- 10% Max Discount
- 15% Max Discount
- BMW
- Diesel
- Dodge V8 Platforms
- Ford
- Honda
- Hurricane I6
- Mercedes
- Mitsubishi
- N/S63TU
- No Discount Products
- Porsche
- Powersports
- Tier OBD
- Toyota
- Uncategorized
- Universal
- VTT
- VTT-FAB
- VTTEV
- VW/VAG