-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT- S55 / N55 PCV Delete kit
$99.99 – $399.99Price range: $99.99 through $399.99Have a problematic PCV on your S55/N55 powered BMW, don't want to pay to replace the entire VC? The VTT PCV delete kit is just what you need. This kit blocks the factory PCV from pulling from the head ports, gets rid of the tear-prone rubber diaphragm, and essentially converts your VC into VTA through the factory front port on the VC. This kit can work stand-alone with the cap, and a -10 ORB plug, can be used to run an extra breather port, or it can be installed with any Catch Can kit that uses the front port of the stock VC. Simply remove the factory cap, take out the diaphragm, screw the plug into the center port, and tap the new cap on with a soft blow hammer or similar. This deletes the PCV and allows you to avoid the issues of a failed diaphragm. Kit Choices- Cap and -10ORB plug only (to be used with an existing catch can or VTA)
- Cap and Catch can kit (recirc or VTA) Complete kit to delete the PCV, and run a catch can (Currently works with S55 only)
- Cap Only (To be used if routing an additional hose from the cap to location or set up of choice, requires your parts to work)
- 1 PCV Cap
- 1 PCV port block off Plug
- 1 -10 ORB Plug
- Optional Catch Can kit
-
Quick View
S55 M3/M4 Silicone Charge Pipes Bundle
From: $409.99VTT silicone Charge Pipes are the premiere choice for your EBM Charge Pipe needs. Made from high quality, wire impregnated silicone, these inlets are a full 6mm thick, and can withstand even the harshest underhood conditions. -
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewS55 Cold side “J” charge pipe
$121.12 – $161.49Price range: $121.12 through $161.49 -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT BMW Plug and Play Pre AND Post throttle 5-Bar (58 psi), 6-Bar(72 psi) Map Sensor Kits
$177.49 – $209.99Price range: $177.49 through $209.99Looking to up your boost limit on just about any BMW vehicle that runs a 3 or 4-wire BMW map sensor including but not limited to S58, B58, N54, N55, S55, S63, B48, B47, B42, B57, B46? We were too, so we decided to make a very easy plug-and-play kit for 3, and 4-wire BMW map sensors. These kits will allow you to completely replace the 3-wire sensor with one of our sensors, leave your stock 4-wire in place for IAT sensing, and move the power, ground, and sensor signal from the factory sensor to our sensor. These sensors have the proper scaling which will allow your tuner to simply change your map sensor scaling in the tune, and the factory ECU will be able to utilize the sensor voltage with no problem. We are offering these in 5 bar (58 psi), and 6 bar (72 psi), and each comes with a plug-and-play harness, and optional fittings for ease of installation.Note: For the S58/B58 our Factory style Pre-Throttle map sensor is also 5 bar, and will work fine coupled with the post throttle kit, but the scaling is different, if you want matching Voltages Pre/Post throttle you can run two of these.
A variety of install pics can be found below and - Here
Scaling PDF Links: 5-Bar / 6-Bar
Features include:- Plug and Play harnesses with no wire splicing
- Output wire for connecting a PI or external controller to your post-throttle map sensor for the most stable signal that is not affected by throttle closure
- Different fittings are available for your plumbing needs.
- Can have matching voltage signals for pre/post throttle for ease of tuning, and boost reference
- B58/S58 etc Pre Throttle - 3 Wire Harness (Charge pipe to 1/8" NPT adapter needed, for B58/S58 90 degree adapter needed to provide sensor clearance)
- B58/S58 Post Throttle - 4 Wire Harness (Boost reference will be needed from manifold to sensor)
- F90 M5 Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- Most all other platforms Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- B58
- S58
- S63/ S63TU
- N63
- N54
- S55
- N55
- N20
- B46
- B48
- B57
- B47
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsNeed a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Billet Non-Marring Double Ended AN wrenches
$12.99 – $149.99Price range: $12.99 through $149.99Secure Your AN Fittings the Right Way – Without the Damage
VTT now offers a complete line of precision Billet 6061-T6 Aluminum AN Wrenches, designed to grip without marring your fittings. Whether you're working with -3 or -20 AN sizes, we've got you covered.These wrenches are lightweight, durable, and anodized in 8 vibrant colors for a long-lasting finish and easy size identification.
Available Options:
-
Full Kit: Includes all sizes from -3 to -20
-
Common Size Kit: Includes -4, -6, -8, -10, and -12
-
Individual Wrenches: Purchase only the sizes you need
-
-
Quick ViewAdding a Front-facing manifold to your N54, and need to extend your map sensor harness? We got you covered with ur 24" extension harness. High-quality wiring, with seating, and our own 3D printed connectors ensure a perfect fit.
Product categories
- 10% Max Discount
- 15% Max Discount
- BMW
- Diesel
- Dodge V8 Platforms
- Ford
- Honda
- Hurricane I6
- Mercedes
- Mitsubishi
- N/S63TU
- No Discount Products
- Porsche
- Powersports
- Tier OBD
- Toyota
- Uncategorized
- Universal
- VTT
- VTT-FAB
- VTTEV
- VW/VAG