-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Billet N54 PCV Cover & Valve Upgrade
$14.99 – $63.99Price range: $14.99 through $63.99Upgraded PCV valve for your N54 engine. We always recommend upgrading your PCV valve at the time of turbo upgrade or replacement, as the stock valve can be worn. This means it can stop functioning to its full potential, causing oiling issues with your BMW. This upgraded valve not only replaces the worn stock valve, it is also much stronger and will help eliminate any future PCV issues.Kit Includes:
-
1x Billet PCV Valve Or 1x Billet PCV cover
- 1x complete kit with PCV Valve, and PCV cover (Save 15%)
-
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT BILLET BMW N54/N55/S55 Crank Seal Guard
$84.99 – $179.99Price range: $84.99 through $179.99VTT BILLET BMW N54/55 Crank Seal Guard.
It is a well-known issue on the BMW N54/N55/S55 platforms that your serpentine belt can fail for various reasons, when this happens you have a high chance of the belt getting sucked behind the front damper, and then being pushed past the crank seal into your oil pan. From there it can get sucked into the oil pick up causing total engine failure, even if you do not lose the engine it is a COSTLY repair to remove the sub-frame and drop the oil pan to remove the belt. The best way to combat this is to watch for oil leaks and keep up on your maintenance. BUT Even with those preventative measures, pre-mature belt failure can occur. This crank seal guard installs over your front crank seal and will keep the belt from being sucked in if a belt failure does occur. This is a cheap way to ensure you do not end up having to replace your motor from oil starvation due to an ingested belt. Our seal is different from those already on the market, firstly it is not offensively priced. Secondly, it is 100% billet, with no welds on the tabs to break, no cheap bent thin steel pieces. 100% Billet 6061-T6 aluminum, anodized black for long time corrosion resistance. Crank Seal comes with- One VTT Billet N54/55 Crank Seal Guard
- Two extended 12.9 Grade bolts, and two stainless washers
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Upgraded Silicone N54 coolant hose kit
$19.99 – $464.99Price range: $19.99 through $464.99VTT Upgraded Silicone N54 Coolant Hose Kit
Upgrade Your N54 Cooling System with High-Performance 6-Ply Silicone Hoses. NOW WITH TWO FITTING CHOICES! Billet or OEM Style
Looking to replace your worn-out N54 coolant hoses with a high-quality, durable upgrade? Want a cost-effective solution without opting for billet adapters? Vargas Turbo Technologies (VTT) has you covered!
We now offer our N54 upgraded silicone coolant hose kits featuring OEM-style direct-fit factory connectors, ensuring a seamless and reliable installation.
ā Key Benefits:
- Premium 6-Ply Silicone Construction ā Handles up to 200 PSI for superior durability.
- BILLET OR OEM-Style Factory Connectors ā Direct fit with no modifications required.
- Multiple Color Options ā Available in Red, Black, or Blue to match your engine bay aesthetic.
- All Hoses In Stock ā Choose your preferred fitting style and color at checkout.
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVTT BMW Billet One Way Crankcase Breather VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, and remove crankcase pressure, all while adding a cool look to your engine bay. Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one-way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.This breather will fit MOST NOT ALL BMWs with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54, S85, S63, S63TU, N63. There are factors that may stop it from fitting your platform such as valve cover style etc.
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / Details -
Quick ViewThis kit comes with 1 set (both turbos) of Stainless Steel wear matched bushing, and flapper assembly, Wastegate arm, rod end, and Stainless steel 8mm C clip.
-
Quick View
VTT N54 Crank Bolt Capture
$127.49The VTT N54 crank bolt capture. slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub, meaning it cannot back out no matter what. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Ignition Coil Kits
$169.99 – $222.49Price range: $169.99 through $222.49VTT is proud to offer ignition coil replacements for the N5X platforms, as well as B5X, and many VAG platforms. We started our quest for coils by contacting multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once we were satisfied with the testing, we had the best performing coils made to our colors and specs. We offer these coils as complete sets for the N54, B58/S58, and the VAG platforms in either 4, or 5 cylinders. We also offer upgraded plugs which are highly recommended to change when doing coil replacements These coils come in 3 colors, Red, Black, and Blue, and are not simply an aesthetic upgrade but match or exceed the factory secondary spark energy. The VAG coil, is extremely potent, and the tester was so impressed with it compared to the factory coil, he called it a "BEAST" of a coilNote:Ā To extract maximum performance from VTT coils minor tune changes are required to optimize dwell periods. See recommended Dwell times below
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewN54 Aluminum Turbo Outlet
$242.49 -
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA well-known issue with the N54 and early N55 with Hydraulic power steering is the plastic pulley either hitting the subframe, or simply breaking on its own, this can cause the belt to be ejected from the pulley, and leave you stranded with no serpentine belt. To top it off if you continue to run the vehicle with the belt off, you also have a good chance of sucking the belt into the engine through the front seal. Put an end to the dreaded plastic PS pulley issues with our 100% Billet Aluminum PS pulley. We make these from 6061-T6 aluminum and anodize them in one of 4 colors (Black, Red, Blue, and Clear) for a great look, and long-lasting finish. These weigh 11Oz, very close to the weight of a stock pulley, and are lighter than the cast aluminum versions on the market. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT BMW/Toyota Conversion Wheel Spacers
$59.99 – $74.99Price range: $59.99 through $74.99Looking to convert your 5Ć120 or 5x112 vehicle to 5x114.3 wheels, or 5x120 wheels, and open up your wheel options DRAMATICALLY? We got covered with our VTT wheel spacer conversion kits. These kits are machined from billet 6061-T6 aluminum and anodized for a long-lasting finish. We then press in 10.9 class studs, with corrosion-resistant zinc coating for years of use. The spacer then accepts either a 5x114 wheel or a 5x120 wheel. The 5x114 use M14 studs, and the 5x120 use M12 studs. All the spacers have either a 66.6mm or 72.6mm Hub bore size to fit 99% of BMW applications, and we offer Hub-Centric adapter rings to fit other wheel bore sizes No wobble bolts or redrilling here. We offer these in 4 thicknesses 15mm, 17.5mm, 20mm, and 25mm. The studs coming out of the spacer areĀ 40ā³ total length and come with Black Lugnuts. Spacers that convert to 5x120 have M12 studs, ALL others have M14x1.5 -
Quick View
N54 OEM Replacement Kit (Fits all N54 models LHD & RHD)
From:$1,379.98Original price was: $1,379.98.$1,379.97Current price is: $1,379.97.WHP Level supported (with proper fuel, upgrades, and tuning) Stock - 500WHP -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Cold Side Charge Pipe
$94.99 – $127.49Price range: $94.99 through $127.49Whenever upgrading your N54 we suggest going to a true BOV like a Turbosmart Raceport. This cold side charge pipe allows you to do that while getting rid of the prone to cracking plastic charge pipe, and plastic DV's. If you do want to keep the DV set up, we also offer a DV charge pipe. Also available for N55 with no bungs at all, as the DV is on the turbo. Looking for the Charge Pipe & BOV Combo? Click Here -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Oil Block Off Plate
$59.99 – $64.99Price range: $59.99 through $64.99VTT CNC Oil Block off the plate. Use these when you want to delete the stock coolers lines, and run two -10 fittings for your aftermarket oil cooler set up. These provide full flow and get rid of any restrictions. We offer these in THREE colors to match out other N54 billet engine parts such as Oil Cap, PS cap, and Oil Filter housing cap. Available as plate only, with -10 fittings, or -8 fittingsWe suggest running an aftermarket thermostat with a block-off plate to help warm the car up quickly.
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / Details-
Introducing the VTT OBD-LOCKĀ ā Enhanced Security & Improved Design!
We are excited to announce our OBD-LOCK! This latest version has been completely redesigned for improved strength, ease of installation, and enhanced protection. Key upgrades include:
ā No more OBD port penetration ā eliminates any risk of damage
ā Revised thread style ā prevents stripping for a secure fit
ā Stronger, more durable design ā ensures maximum securityUltimate OBD Port Protection
The VTT OBD-LOCK is precision-machined from billet 6061-T6 aluminum and is engineered to completely lock out your OBD port, preventing unauthorized access.
š Anti-Theft Protection ā Prevents thieves from accessing the OBD port to duplicate keys or disable security systems
š Dealer/Tech Lockout ā Stops unauthorized tune changes or system modifications
š Tamper-Proof Design ā Cannot be removed without physically destroying the OBD port unless the correct tool is usedVTT OBD-LOCK ā Version 2 NON-GM
Universal Fit for All Non-GM (General Motors) VehiclesThis device is compatible with all non-GM vehicles, including but not limited to:
-
All VAG group vehicles (VW, Audi, Bentley, etc.) ā including recessed port VW/Audi models
-
Ford, Nissan, Honda, Toyota, Porsche, Dodge, Ram, Jeep, Kia, Subaru, and more
Not compatible with GM (General Motors) vehicles.
VTT OBD-LOCK ā Version 2 GM
Universal Fit for GM (General Motors) Vehicles ONLYThis version is specifically designed for General Motors vehicles, including GM, Chevrolet, Cadillac, Holden, and other GM-branded models.
If your vehicle is anything other than a General Motors product, you will need the Non-GM version.
-
-
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT BMW Billet Coolant Reservoir Cap
$79.99 – $189.99Price range: $79.99 through $189.99VTT is proud to offer our billet replacement for the factory plastic Coolant Reservoir cap. This cap does away with the weak plastic cap while adding some pop, and color to your engine bay. These Coolant caps retain ALL of the factory provisions by simply allowing you to snap the factory pressure-relief into the new Billet Cap We also designed these caps to complement our N5X Billet Oil caps, N5XBillet Oil filter housing caps, and Billet Power Steering cap and so all 4 will have the same design. We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize, as well as a choice of custom anodize at a cost of $100 extra. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT N5X/S55/N2X Billet BMW Oil Filter housing Cap
$89.99 – $199.99Price range: $89.99 through $199.99VTT is proud to offer our billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap, and the need for a special tool for removal, while adding some pop, and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. We also designed these caps to complement our Billet Oil caps, and upcoming Billet Power Steering caps, so all 3 will have the same design. Order all 3 - Oil Cap, Oil Filter housing Cap, and Power steering cap for $175 - 10% savings We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize, as well as a choice of custom anodize at a cost of $100 extra. The cap has a 19mm hex for easy installation, and removal, and includes a new sealing O-ring, and a small O-ring for the oil filter cage. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewN54 Silicone Inlets
$349.99 – $359.99Price range: $349.99 through $359.99VTT silicone inlets are the premier choice for your N54 inlet needs. Made from high quality, wire impregnated silicone, these inlets are a full 6mm thick, and can withstand even the harshest underhood conditions. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT M14/M12 Titanium Wheel Stud kits
$169.99 – $339.99Price range: $169.99 through $339.99VTT is proud to offer Titanium wheel stud kits for the owner looking for the lowest possible unsprung weight while maintaining high strength, and good looks as all come with an amazing burnt finish. This kit is 60% lighter than factory steel studs and nuts with a total kit of 20 nuts, and studs being 3.1LBS. Sets of 10 are 1.55 lbs -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Billet Check Valves
$27.99 – $31.99Price range: $27.99 through $31.99VTT CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi. -
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVTT is proud to offer our billet replacement for the factory plastic vacuum tanks that store vacuum from the pump and use it to regulate boost via the solenoids. The stock plastic can, and small plastic nipples on the stock cans have a tendency to crank over time, and if they leak you will get low boost, or no boost, and poor performance. These cans do away with the weak plastic cans while adding some pop, and color to your engine bay. These vacuum cans retain ALL of the factory provisions including mounting points but come with 90-degree fittings for easier routing of the lines We also designed these cans to complement our N54 Billet lineup - N5X Billet Oil caps, N5XBillet Oil filter housing caps, Billet coolant cap, Billet valve cover, billet oil cooler block off plate, and Billet Power Steering cap and so on. All will have matching color We offer these cans in 4 colors - Red, Black, Blue, and Clear anodize -
Quick ViewBuy all 5 Fittings and Save $6. This product includes all of the fittings listed below.
-
Quick View
VTT “GC” N54 to B58 Coil Conversion Kit
From: $339.99VTT is proud to offer its very own Game Changer N54 to B58 Coil conversion kit for the BMW N54 platform. The N54 has notoriously had ignition problems with the factory coils, while aftermarket upgrades do exist, they can be bulky. While factory coil upgrades such as S55, and our own N54 coil upgrades do provide more spark, the BMW B58 ignition coils are extremely robust and can support well over 1000WHP with no issues. This means a plug-and-play affordable solution that fits like stock, and looks AMAZING doing so! We designed our own 6061-T6 Billet bracket in a plethora of colors including matching shades for every N54 Valve Cover we offer (even the cast wrinkle), and we even went as far as to have some cut-out of 100% carbon fiber sheet for the unmistakable look, and lightweight that only carbon fiber can offer! This means you can mix and match the color of the bracket with coil color, with VC color to truly tailor your engine bay to look exactly how you want it to!Note: Flash setting changes are required when installing the conversion kit to ensure the proper function of the B58 coils with N54 DME. This can be found in most all flashing software settings such as MHD, Bm3, etc.
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Billet N54/N55 Vacuum/Boost Adapter
$53.99 – $69.99Price range: $53.99 through $69.99We are happy to release our BMW B54/N55 (Limited N55 Fitment) vacuum/boost adapter. These go inline with the Throttle Body fitting and provide a full boost/vacuum signal from the manifold. This fitting adds two 1/8NPT bungs to accept any fitting that has 1/8" NPT threads. You can choose options, 1/4" barb, as well as 1/8NPT plugs if you only want one barb, etc. These are perfect for running your PI off manifold pressure which is much more accurate than charge pipe, and they are also great for BOV running the proper size line without having to drill a hole in your manifold. These do space out any sensors etc giving inaccurate readings like some of the other brands do. They are made from 6061-T6 anodized black, with steel plugs, and Blue Anodized barbed fittings. You can choose to order in a few ways. You can choose straight or 90-degree barbs. Adapter alone - $40 Basic kit - 1 Adapter, 1 barb, and one plug, one vacuum cap, and one zip tie $45.00 Dual Barb kit - 1 Adapter, 2 barbs, one vacuum cap, and one zip tie $55.00 -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT N5X/M5X/N2X Billet Power Steering Cap
$79.99 – $189.99Price range: $79.99 through $189.99VTT is proud to offer our billet replacement for the factory plastic Power steering cap. This cap does away with the weak plastic cap, while adding some pop, and color to your engine bay. These Power Steering caps retain ALL of the factory provisions including dipstick, and vent hole We also designed these caps to complement our N5X Billet Oil caps, and N5XBillet Oil filter Caps caps, so all 3 will have the same design. Order all 3 - Oil Cap, Oil Filter housing Cap, and Power steering cap for $175 We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize, as well as a choice of custom anodize at a cost of $100 extra. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewN54 CHRA REPLACEMENT OEM / STAGE 1
$589.99 – $1,289.99Price range: $589.99 through $1,289.99Need N54 turbo replacements, don't have full turbo replacements in your budget,Ā like wrenching on your own stuff? If you answered yes to any of those questions, the VTT N54 CHRA replacements are perfect for you! -
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsDo you work on BMW engines across multiple platforms? Tired of modifying universal engine stand plates just to make them fit? Frustrated by losing access to the flywheel side once the engine is mounted?
We were tooāso we built the solution.
The VTT BMW Engine Stand Plate is a true bolt-on design that keeps the flywheel end fully accessible while providing a strong, stable mounting solution for your engine builds.
Machined from solid 6061-T6 billet aluminum and anodized in five colors for long-term durability and corrosion resistance, these plates are lightweight yet rated for over 1200 lbs.
Fitment: N54, N55, S55, B58, S58 (more coming soon)
- Note: The stand tube is 60mm or 2.36ā OD, which fits most engine stands, but not allāplease measure before purchasing.
Key Features:
- Lightweight, high-strength billet 6061-T6 construction
- Durable anodized finish
- Direct bolt-on to intake-side motor mount location
- Full clearance for accessories and flywheel/flex plate access
- Built-in provisions for locator pin and rotation bar
-
Quick ViewLooking for a little extra clearance on your coolant tank fitting due to relocation for single turbo, forward-facing intake manifold, etc. This 90-degree fitting will allow you to run the hose straight down instead of straight out, and increase your clearance, and routing choices. Made of 6061-T6 and anodized black for a long-lasting finish. Comes with fitting, and 1 clamp.
-
Quick ViewThis is an easy way to order all 3 VTT Billet engine caps for Valve Cover, Power steering, and Oil Filter Cap. We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize, as well as a choice of custom anodize at a cost of $399 total for custom
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT N54 “Spline Lock” CrankHub Solution
$819.99 – $939.99Price range: $819.99 through $939.99VTT āSpline Lockā Crank Hub System ā N54 / N55 / S55
VTT is proud to offer theĀ only complete crank hub solutionĀ for BMW N54, N55, and S55 engines thatĀ does not require drilling the crankshaft for pins.
Our innovative hub features proprietaryĀ Spline Lock Technologyāa high-tolerance, precision-machined spline system that presses into the crank andĀ positively locks the hub in place, eliminating the need for traditional pinning or welding.
After months of rigorous development and over 10 different prototype revisions, our final production version was put to the test. In our in-house trials, the hub outperformed expectationsābreaking our testing rig before it ever slipped. Real-world validation has been conducted on the VTT N54 race car, which spins toĀ 8,000 RPMĀ and produces overĀ 900 WHP.
Key Benefits:
-
No crank drilling requiredĀ ā stock-like installation
-
Minimal laborĀ ā fully reversible with no permanent modification
-
Tested to extreme conditionsĀ ā race-proven at high RPM and power
-
Exclusively compatible with VTTās Crank Bolt Capture (CBC)Ā for maximum security
ā ļøĀ Spline Lock hubs are recommended be used with the VTT Crank Bolt Capture system. They are not intended to run independently.
-
-
Quick View
N54 Head Port Block Off Kit
$37.99VTT Head Port Block-Off Kit
The VTT Head Port Block-Off Kit is designed to seal the built-in ports in the cylinder head that utilize engine vacuum to clear the low-side PCV system. This factory setup can draw oil into the intake manifold, leading to valve carbon buildup and other unwanted issues.
Kit Includes:
-
6 precision-fit set screws
-
Engine-specific tap
This kit is compatible with N54 engines. Each kit is supplied with the correct tap for your specific engine type.
-
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT N54, N55, S55, N20, B58 Billet Motor Mount Inserts
$179.99 – $474.99Price range: $179.99 through $474.99 -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Thermo-Isolating O2 Bungs
$52.49 – $84.99Price range: $52.49 through $84.99Price is for Single Bung only. -
Quick ViewAre you building a single kit for the N54, N55, or S55 platform? The stock studs are usually a little bit short for most single-head flanges, and finding M7 studs is not easy. So we made our own longer studs to combat the issue. Made from 10.9 grade steel, and coated in black oxide, these are the perfect solution to the short stud problem. Sold individually so order the number you need. Stud details are as follows
- Overall length 47mm (stock 39mm)
- 3mm shoulder
- 6mm head which is 5mm hex
- 14mm short end
- 24mm long end (stock 15mm)
Dont forget our M7 copper lock nuts as well to complete the job - https://vargasturbo.com/product/vtt-fab-m7-copper-locking-exhaust-nuts/
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT PCV Delete fitting
$53.99 – $79.99Price range: $53.99 through $79.99 -
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVTT is proud to offer a Titanium hardware upgrade for all our Billet and Cast VC's. This will come with M6x30 Ti bolts N54 /N55/S55/B58 Gen 1/ B58 TU it will be an Umbrella head with a 16.3mm head. These bolts weigh half as much as comparable steel hardware and look amazing. Colors to choose from will be Burnt, Black, and Natural (silver) -
Quick View
VTT Modular Cast Aluminum CNC Valve Cover Kit
From: $967.44VTT Cast Aluminum Valve Cover ā N54
Upgrade your BMW N54 with VTTās Cast Aluminum Valve Coverāa durable, high-performance alternative to the factory plastic cover. This version offers the same precision machining as our billet model, but at a lower cost, making it the best bang-for-your-buck valve cover upgrade.
By eliminating the factory PCV system, this valve cover allows full customization of your PCV setup. It is also fully modular, meaning it seamlessly integrates with all VTT PCV fittings, breather options, and accessories.
Built from aircraft-grade aluminum, powder-coated in three bold colors, and fully baffled to prevent unwanted oil escape, this cover is a must-have for N54 owners seeking longevity, reliability, and performance.
Key Features & Benefits:
ā Cast CNC 6061-T6 Aircraft-Grade Aluminum Construction ā Built for strength and durability
ā Powder-Coated in Multiple Colors ā Choose from Black Wrinkle, Blue Wrinkle, or Red Wrinkle for a flawless finish
ā Lightweight Design ā Weighs 9.0 lbs (compared to 7.9 lbs for the stock coverājust a 1.1 lb difference)
ā Fully Modular PCV System ā Compatible with all VTT PCV fittings, breathers, and accessories
ā Cost-Effective Alternative ā More affordable than other non-modular cast options
ā Fully Baffled Ports ā Prevents unwanted oil escape
ā Direct Fit for BMW N54 Engines ā Includes a new factory gasket and all required installation hardware -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Modular PCV/Catch Can (Ready to install kits)
$232.49 – $474.99Price range: $232.49 through $474.99VTT Ultimate Modular Valve Cover & PCV System
VTT is proud to introduce a ground-up system that gives the end user complete control over their valve cover and PCV setup. Tired of being told you must run two -10AN lines from your valve cover to your catch can? So were we. This system allows you to configure it exactly how you wantārun it fully VTA, use an oil cap one-way breather, or create your own hybrid setup. Nothing else on the market matches the versatility and functionality of this modular system.
Itās the ULTIMATE Valve Cover & PCV Comboāor choose just the components you need. Run as many or as few connections as you like.
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT VAG/BMW/TOYOTA Billet Wheel Spacers
$21.99 – $37.99Price range: $21.99 through $37.99VTT Billet Wheel Spacers
VTT is proud to offer billet wheel spacers for most VAG, BMW, and the A90/91 Toyota Supra platforms.
Each spacer is:
-
CNC-machined from 6061-T6 aluminum
-
Hard anodized black for a long, corrosion-free life
We offer multiple fitments and sizes to suit a wide range of applications.
THESE ARE SOLD INDIVIDUALLY, FOR ONE AXLE ORDER TWO FOR A COMPLETE SET ORDER FOUR.
ANYTHING OVER 5MM WILL REQUIRE LONGER BOLTS OR STUDS. YOU CAN CHOOSE TO ADD A VTT WHEEL STUD KIT FROM THE OPTIONS.
PLEASE DOUBLE CHECK YOUR BOLT PATTERN AND HUB BORE BEFORE YOU ORDER. INSTALLED SPACERS CANNOT BE RETURNED!
-
-
Quick View
N54 Stage 1 Upgrade Kit (Fits all N54 models LHD & RHD)
From: $2,039.99WHP Level supported (with proper fuel, upgrades, and tuning) Stock - 525WHP -
Quick View
VTT PCV Flapper delete
$59.99Made of 6061-T6 aircraft aluminum anodized black, comes with O-ring, and stainless steel holding clip -
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe stock outlet adapter on the N54/55 is NOTORIOUS for cracking when removing. This Billet replacement ensures no leaks, and no more cracked adapters. Available in 6 colors! Black, Red, Clear, Blue, Purple, Gold -
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVTT is Proud to offer our Billet Aluminum DCT Transmission pan. This pan does away with the factory plastic pan and upgrades it to 6061-T6 aluminum anodized in a variety of colors. This pan increases fluid capacity by 80% or almost DOUBLE the stock pan, has a US-made reusable Viton Gasket, a rare earth magnet built in to pull metal from the fluid, machined external fins to help aid in cooling, and a -6 ORB drain plug. Product Features:- Billet constructionĀ using 6061-T6 aluminum for long life, and added strength
- 80% or Almost DOUBLE the factory fluid capacity at 2000ML compared to 1150ML
- Machined fins for improved cooling
- Rare Erath magnet built in to pull metal from the fluid
- US-Made Viton Gasket
- -6 ORB drain plug for easy service
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT-FAB Billet Mac Solenoid brackets
$49.99 – $53.99Price range: $49.99 through $53.99Building a kit using Mac solenoids to control boost? Need an easy way to mount it? VTT-FAB has you covered with our billet Mac Solenoid brackets. Machined from 6061 billet and anodized in 3 colors, these are the perfect way to mount your Mac valve and look good while doing it. Each kit includes:- One Mac Solenoid bracket (3-Port or 4-Port)
- 2 Allen screws to hold the valve to the bracket
- M6 Moutning Bolt
-
Quick ViewAre you building a single kit for the N54, N55, or S55 platform?Ā M7 Locking exhaust nuts is not easy. So we made our own to combat the issue. These are the perfect solution to the problem of hard-to-find M7 lock nuts. Sold individually so order the number you need.
Note:Ā This is nuts ONLY Stud not included, by our extended M7 studs here - https://vargasturbo.com/product/vtt-fab-extended-m7-n54-n55-s55-b58-2-port-head-studs/
-
Quick ViewLooking to make sure all metal contaminates that are possibly in your oil are not circulated? VTT has you covered with our Titanium Magnetic oil drain plugs for BMW, and any other vehicle that uses an M12x1.5 drain plug. This drain plug will capture any ferrous metal in your oil, and capture it to be cleaned during your next oil change. It also is stronger than a Steel or Aluminum drain plug, and looks cool! These are made from GR5 Titanium and use a rare earth magnet to capture metal particles in your oil... Kit includes:
- 1 Titanium Drain Plug
- 1 M12 Crush Washer
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT VC, and Catch can kit. ALL YOU NEED
$1,289.99 – $1,859.99Price range: $1,289.99 through $1,859.99One of the most common emails we get here at VTT is regarding VC set up with catch cans, and which fittings to pick, how to set it up, etc. This kit does away with all of that, and we give you exactly what you need to g to external PCV on the N54 from the experience of installing hundreds of kits. -
Sale!Quick View
VTT Cold Side Charge Pipe / Turbosmart BOV Kit
$409.99Original price was: $409.99.$409.79Current price is: $409.79.A plug and play BOV option for your N54. This kit comes with everything you will need to replace your undersized factory DV with a high quality Turbosmart Race port. -
Quick ViewLooking to remove the HPFP or DI system on your N54? this plate will block the vacuum pump and prevent oil leaks. You will need to remove any fuel lines, etc. Kit includes
- Block Plate
- 3 bolts
- O-Ring
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / Details -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewCatch Can – Fitting A
$15.99 – $41.99Price range: $15.99 through $41.99 -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Carbon Fiber Dragy Holder
$21.99 – $51.99Price range: $21.99 through $51.99Tired of your Dragy flying all over the car as you try to do runs? Tired of low sats or no sats warning due to improper location of the Dragy in the vehicle? Well say goodbye to those issues with our new Carbon Fiber and Plastic Dragy holders. These are made from either 100% Pre-Preg Carbon Fiber, or molded plastic for a perfect fit. The carbon fiber gives it just the right look to add to your performance vehicle! Each holder has dual Suction cups and will stick to any smooth surface. We suggest mounting them in the upper left or right corner of your windshield with a full view of the sky. Dragy holder features- Stop your Dragy from flying off the dash, and having to search for it
- Position your Dragy in the optimal position for the best satellite coverage
- VTT Dragy holder exposes the entire top of the Dragy so nothing is blocking the receiver from the Satellite
- The charging port is not blocked and can be accessed with the cover on
- Choose from REAL Carbon Fiber or Molded Plastic
-
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT BMW Carbon Fiber Driveshaft
$1,699.99 – $1,878.49Price range: $1,699.99 through $1,878.49VTT Carbon Fiber Driveshaft for BMW Applications
Why overpay for a carbon fiber BMW driveshaft?
VTT is proud to offer a premium carbon fiber driveshaft manufactured exclusively for VTT in the USA by GCDS (Gulf Coast Driveshaft) ā one of the premier driveshaft manufacturers in the country with extensive experience in high-performance and drag racing applications.
Each driveshaft is constructed using 3.31" carbon fiber tubing, paired with NEAPCO Performance 1350 series U-joints, then bonded using a proprietary high-strength process and precision balanced to within 1/8 in-oz as a complete assembly.
Every shaft is torque tested in-house prior to shipping to ensure proper bonding and structural integrity. GCDS and VTT are among the few manufacturers that perform full torque testing on each shaft before it leaves the facility.
To complete the system, the driveshaft is paired with VTT-designed 7075 aluminum adapters, eliminating the factory guibos and unnecessary flex points. The shaft connects directly to the BMW 3-bolt front flange, while a VTT 4340 rear adapter replaces the factory slip-in / screw-retained shaft design for improved strength and reliability.
Proudly Made in the USA.
PLEASE NOTE! YOU MUST SEND US YOUR VIN NUMBER TO PROPERLY PROCESS YOUR ORDER, IF YOU DO NOT SEND YOUR VIN, YOU ORDER IS GOING TO BE HELD
PLEASE NOTE! Driveshafts can have UNUSUALLY LONG LEAD TIMES. We hope to reduce this with GCDS, but if the shaft shows OUT OF STOCK, expect a lead time of 4ā8 weeks, unless we specifically state that it can ship sooner.
Due to the nature of these shafts being manufactured by a 3rd party, ANY ORDERS PLACED FOR VTT CF DRIVESHAFTS ARE 100% FINAL.
NO REFUNDS. NO CANCELLATIONS. FOR ANY REASON.
THIS INCLUDES LONG LEAD TIMES.
PLEASE ORDER CAREFULLY. ONCE THE ORDER IS PLACED, IT IS FINAL.
-
Quick View
N54 Stage 2 Kit (Fits all N54 models LHD & RHD)
From: $2,329.99WHP Level supported (with proper fuel, upgrades, and tuning) Stock - 625WHP -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewReplacement Gasket for VTT Valve Covers
$31.99 – $69.99Price range: $31.99 through $69.99Need to replace the gasket on your VTT Aluminum VC? Simply choose your model from the dropdowns to ensure you get the correct version. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT N54/55 BMW Single Piece Silicone Cold Side Charge Pipe
$112.49 – $464.99Price range: $112.49 through $464.99VTT is proud to offer the very best charge pipe solution for the BMW E Series N54/55 platforms. This system completely does away with the restrictive, and muli-connection stock charge pipe system, and replaces it with a single 6-ply, Heat Resistant, Wire reinforced silicone charge pipe rated at over 200 psi.FITMENT:
ā¢ E Series N54 vehicles 335, 135 (Does not fit Z4, and 5 Series) ā¢E Series N55 vehicles 335, 135 (Does not fit SUV or other models) -
Quick View
VTT N54 “DI Injector” Delete Kit
$339.99Looking to get rid of the troublesome and expensive DI injectors on your BMW N54 and move to PI only and a standalone? If so VTT has you covered with its new N54 PI delete kit. This kit allows you to SAFELY remove the DI injectors, install our delete fittings, and run PI only. We machined these deletes from 310 Stainless for extreme heat, and corrosion resistance, and include 3 hold downs. These DI deletes COMPLETELY get rid of all factory provisions, including the seal. If the seal is left intact with no fuel to cool the injector or delete it will quickly overheat and melt the delicate seal causing combustion gasses to escape the engine creating misfires, and worse possibly damaging your injector bore on the cylinder head. Our deletes are machined to be a press fit into the cylinder, and can be either cooled with liquid nitrogen, and dropped in, or tapped in with a hammer, and then held down with the included hold downs. We also include M6 tapped holes on the top of each one in case they need to be removed you can attach a slide hammer, and remove the delete. These are sold as a kit and come with the following- 6 - 310 Stainless DI Delete fittings
- 3 - Hold down brackets
EXTREME ENGINE MODS ARE REQUIRED TO RUN THIS KIT, PLEASE SEE BELOW
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Billet Crankcase Breather replacement filter
$21.99 – $27.99Price range: $21.99 through $27.99Need a replacement filter for your VTT Billet Crankcase breather? You can order on here. We offer them in 3 heights, low 48mm, medium58mm, and tall 68mm. This is measured from base to top. The filter will include a new clamp. For reference: N54/55 mostly use the low A90 Supra use Medium Most Audi applications can fit a tall, but measure your filter before ordering. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT “Spline Lock” Hub Puller
$74.99 -
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVTT is proud to release our very own center feed N54 intake manifold.Ā This is NOT the SAME sheet metal manifold everyone is selling with a different logo on it, this is a ground-up design focusing on utility as well as increased flow capability. We performed CAE/Multiphysics simulation for both steady and unsteady state operating conditions in order to bring real-world performance benefits to your N54 build.Ā Our manifold is stronger, outflows the OEM manifold, and installs just as easily as your stock piece (no custom charge pipe or throttle body harness required).Ā Performance gains of 20-30WHP+ were had with no tune changes on a 570WHP stock motor F-RB lite turbo car at the top of the RPM range where it matters most for performance.Ā These numbers will only increase with ported heads, high lift cams, or even higher horsepower builds! -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT BMW M12x1.50 Wheel Stud Kits
$74.99 – $137.49Price range: $74.99 through $137.49Looking to get rid of your factory wheel lugs, and convert them to a high-quality stud kit for track purposes or just to make wheel changes easier? We got covered with our VTT wheel stud conversion kits. These kits are forged cold-rolled steel in 10.9 class, with corrosion-resistant coating for years of use. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT S55/N55 EWG BILLET CNC Valve Cover
$1,519.99VTT S55/N55 EWG Billet Aluminum Valve Cover
Performance. Durability. Style. VTT is proud to introduce our S55/N55 EWG Billet Aluminum Valve Cover, built for owners who want to upgrade both form and function. Whether you're looking to replace your aging plastic OEM valve cover or you're running a single turbo conversion and need better clearance and heat resistance, this cover delivers on all fronts. Designed to eliminate the problematic factory PCV system, our cover allows you to configure your PCV setup exactly how you want it. We strongly recommend pairing it with a catch can for optimal performance. Each unit is fully baffled to reduce oil carryover and ensure clean crankcase ventilation.
š ļø Valve Cover Features:
- ā 100% CNC-Machined from 6061-T6 Billet Aluminum
- ā Anodized Finish in a variety of colors for a clean, custom look
- ā Lightweight Design: 9.7 lbs (vs. 7.9 lbs stock ā only 1.8 lb difference)
- ā Fully Modular PCV Configuration ā run it your way
- ā Fully Baffled Ports to prevent oil escape
- ā A must-have for single turbo conversions ā better clearance and superior heat resistance
- ā Durable & Reliable ā a major upgrade from the OEM plastic cover
š¦ Kit Includes:
- (1) Billet Aluminum Valve Cover
- (1) Set of All Required Hardware
- (1) U.S.-Made Viton Gasket
ā ļø Important Installation & PCV Notes:
When upgrading to an aluminum valve cover, you are removing the factory PCV system and its integrated functionality. If you do not replace it with an external PCV setup, your S55 may smoke or bypass oil under boost or idle conditions. We highly recommend the following:- ā At a minimum, install an external low-side PCV to ensure vacuum at idle, which aids in turbo oil drainage
- ā Block off the head ports to relieve pressure on the valve cover gasket and prevent boost leaks into the crankcase
- ā Pair this valve cover with our Modular Catch Can Kits and Head Port Block-Off Kits for the best results
Upgrade your S55 or N55 with confidenceāditch the plastic, control your PCV, and enhance your engine bay with the VTT Billet Valve Cover. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT CNC ORB Low Profile High Flow Banjo Fittings
$47.99 – $53.99Price range: $47.99 through $53.99Made from CNC 6061-T6 Aircraft aluminum anodized black for a long-lasting finish. -
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT 15″/17″ Drag Pack Wheels for BMW/Toyota/VAG
$256.49 – $341.99Price range: $256.49 through $341.99Looking for a Lightweight, AFFORDABLE drag pack that looks amazing for your BMW, Toyota, or VAG platform? Look no further! VTT is proud to announce our lineup of Drag pack wheels for various BMW/Toyota/VAG fitments! We teamed up with Rota and had them open custom molds for us of their extremely popular Grid design. With these molds, we have an exclusive on 15X10, 17X10, and 17X4.5 wheels in our exact specs. The wheels are currently offered in the colors and sizes belowA variety of Offsets are available, as well as spacers here - VTT Spacers can be found here - https://vargasturbo.com/product/vtt-billet-wheel-spacers/
As well as Center bore adapters here -Ā https://vargasturbo.com/product/vtt-billet-hubcentric-wheel-bore-adapters/Wheels are priced EACH, meaning per wheel
PLEASE NOTE! CHECK FITMENT CAREFULLY. ANY WHEELS THAT HAVE HAD TIRES MOUNTED OR ARE DAMAGED DURING TEST FITTING ETC. ARE NOT RETURNABLE!
We make NO CLAIM these fit ANY PLATFORM, or ANY factory brake set up. It is YOUR JOB to measure, and make sure they will fit BEFORE you mount tires or install them. WE NEVER suggest shaving down brake calipers to fit a smaller wheel. If they do not fit. GET A SMALL BRAKE KIT!
Colors offered:- Satin Black
- Gloss Black
- Bronze,
- Gun Metallic
- 15x10 ET45/ET40 (wheel weight 16 lbs)
- 17x10 ET45/ET40/ET25 (wheel weight 19lbs)
- 17x4.5 ET-20 (wheel weight 16 lbs)
- 15x10 ET45 - (wheel weight 16 lbs)
- 17x10 ET45/ET40/ET25 (wheel weight 19 lbs)
- 17x4.5 ET-20 (wheel weight 16 lbs)
-
Quick View
N54 Stage 2+ Kit (fits all N54 models LHD & RHD)
From: $2,559.99WHP Level supported (with proper fuel, upgrades, and tuning) Stock - 675WHP -
Quick View
N54 F-RB Turbocharger Kit
From: $3,157.47WHP Level supported (with proper fuel, upgrades, and tuning) Stock-850WHP VTT is proud to announce an All-new VTT GC redesign for 2021! The latest in our line of N54 VTT āGCā turbochargers. The GC āF-RBā or Full-Rebrand.ĀThis is an all-new take on the VTT N54 āGCā turbocharger, using 100% new parts throughout that is pure performance. Some of the new groundbreaking features include: All turbine side parts are now fully cast from 310 Stainless Steel for increased temperature resistance, and ultimate corrosion resistance. We also fully redesigned the turbine housing -the F-RB's have a much larger volute as well as a proprietary AR which will dramatically increase flow capacity, helping to eliminate stress on the turbine wheel. Fully redesigned compressor housings which now include V-band OR Hose Barb connection options (while our current stock of hose barb connections last). The CHRAās are redesigned with new compressor wheels, bullet nuts, and better internal parts. These are new turbochargers from the compressor housing to the bearing housing, to the turbine housing, we had them engineered to fit in the stock N54 location, but provide the full flow of a much larger turbo, and providing a flow increase over the V2 āGCā.Ā
With this all-new design, there is no other 850WHP capable turbocharger option on the market single or twins that can match the spool, ease of fitment, power, reliability, OR price of our GC āF-RBāĀ turbochargers!
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Modular BILLET CNC Valve Cover
$1,449.99VTT is proud to announce a ground-up system designed to give the end-user completeĀ control over their valve cover/ PCV set up. Tired of being told you will run two -10 lines from your VC to your Catch Can? So were we. Now you can run them any way you want, including complete VTA, oil cap one-way breather, etc. Nothing on the market comes close to the versatility of this setup, and it truly is the ULTIMATE Valve cover, PCV combo, or Valve cover, or PCV set up. You choose how many or how few you want to run. -
Quick ViewVTT is proud to offer a truly plug-and-play line lock kit for select BMW vehicles that does NOT require running wiring inside the car, mounted switches, holes in the dash, etc. Our newly designed and released line lock kits use a 40amp wireless remote control switch with 4 different modes that allow you to tailor your line lock setup exactly as you prefer. You simply install the solenoids, install the harness with the switch which has all the wiring terminated, bleed the brakes, and you are ready for effortless burnouts which will not be interfered with by the DME because you are holding the brakes, nor wear your rear brake pads. You can store the remote anywhere in your vehicle, center console, cup holder, door cup holder, etc., and when you need to do a burnout to heat your race tires it's in arm's reach without running any wiring into the vehicle. Fitment is confirmed for G8X M3/4, A9X Supra - The kit itself including lines, solenoids, etc will fit most all late model BMW Chassis including F8X, F3X, G2X, etc. The main concern will be mounting the wireless switch in the passenger cowl area. The kit includes:
- Line lock solenoids with weather pack connectors
- Two Parker 90-degree -3 an fittings
- Two Stainless Steel adapter fittings
- Two DOT Approved Stainless Steel brake lines
- One complete wiring harness
- One Remote control switch with TWO remotes
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsWe have heard all the stories about fluid all over the engine bay, seen the headbands, socks, sweatbands, and all the fixes people have used and still have issues with their PS reservoir.Ā So we decided to do something about it, and started with a ground-up design that completely fixed all those issues, and added some much-needed features to an old BMW design. Kit Includes:- 1 PS Reservoir in choice of color
- 2 or 4 fittings
- 2 Hose clamps
- Optional One-Way Breather
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLooking to adapt your wheel bore size to a smaller hub bore? VTT has you covered with our hub-centric adapters. These adapters are made from Billet 6061-T6 aluminum, and anodized in black. We have these sizes currently- 57.1mm hub to 60.1mm wheel bore
- 57.1mm hub to 64.1mm wheel bore
- 57.1mm hub to 66.1mm wheel bore
- 57.1mm hub to 66.6mm wheel bore
- 57.1mm hub to 67.1mm wheel bore
- 57.1mm hub to 70.3mm wheel bore
- 57.1mm hub to 71.6mm wheel bore
- 57.1mm hub to 72.6mm wheel bore
- 57.1mm hub to 73mm wheel bore
- 57.1mm hub to 74mm wheel bore
- 57.1mm hub to 74.1mm wheel bore
- 64.1mm hub to 72.6mm wheel bore
- 66.6mm hub to 72.6mm wheel bore
They are sold in sets of two, order TWO SETS for a full car, or one set per axle.
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT/FF N54 Intake Manifold
$1,399.99THE FAB FACTORY MANIFOLD IS BACK at VTT!
Ā -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Mini Billet Check Valves
$5.99 – $11.99Price range: $5.99 through $11.99 -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT N54 Stock Style Coil Hold Down Kit
$112.49 – $169.99Price range: $112.49 through $169.99Tire of sloppy coil placement with your stock N54 VC? Upgraded to a VTT Cast or Billet VC, and want to run the stock style coils, while positively securing the coils to the plug? We got you covered with our N54 stock style coil hold-down bracket. This kit uses our N54 to B58 coil conversion bracket, with 6 billet S brackets to securely hold your stock style coils in place. This will eliminate any possible misfire issues from coils being raised off the plug, etc. It also looks badass, and can be ordered in all colors to match your existing setup, including Carbon Fiber! -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT External PCV Adapter fitting
$104.99 – $137.49Price range: $104.99 through $137.49Adapter fitting that is required to convert your N54 to external PCV if you want to keep your crankcase under vacuum at idle, and anytime you have a vacuum condition in your intake manifold. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT-FAB Extension Harnesses
$49.99 – $104.99Price range: $49.99 through $104.99Need to move your coolant expansion tank to the other side of the vehicle for a single turbo kit you are building, extend Map sensor plugs, or IAT, how about Throttle Body? Don't cut your factory wires. Just get a VTT-FAB extension harness, and plug and play! These come in various lengths and are covered in expanded sheathing with heat shrink on both ends for a long-lasting, good-looking finish. Available:- Coolant Extension for late model BMW 2015+ 5 ft
- Pre-Throttle Map sensor extension harness 2 ft
- Pre-Throttle IAT Sensor extension harness 2 ft
- B58/S58/B48 etc Throttle body extension harness 2 ft
- B58 to S55 Throttle conversion/extension harness 2 ft
- EWG Actuator Extension harness, Various Lengths
- N54 stock MAP to N20 Map sensor extension
-
Sale!Quick View
VTT Aluminum Outlet & Inlet Bundle Package
$592.48 – $602.48Price range: $592.48 through $602.48Original price was: $592.48 – $602.48Price range: $592.48 through $602.48.$503.61 – $512.11Price range: $503.61 through $512.11Current price is: $503.61 – $512.11Price range: $503.61 through $512.11.Save 15% on your VTT Silicone inlets, and aluminum outlets if you order them together! -
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVTT S55/N55 EWG Cast Aluminum Valve Cover
VTT is proud to introduce our S55/N55 EWG Cast Aluminum Valve Cover, designed for performance-driven BMW owners looking for a durable, stylish, and functional upgrade. This option provides a cost-effective alternative to our billet valve cover while still delivering enhanced engine bay aesthetics and eliminating the failure-prone factory plastic cover, which can crack over time.
Beyond durability, this valve cover removes the problematic factory PCV system, giving you complete control over how you set up your PCV. We highly recommend pairing it with a catch can for optimal performance. Additionally, this cover is perfect for single turbo conversions, offering increased clearance and improved heat resistance.
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Billet BMW N54/N55/S55/B58 “HEAD HANDLER” Cylinder head lifting tool
$69.99 – $89.99Price range: $69.99 through $89.99Do you work on a lot of BMW engines from various platforms? Do you ever struggle with heavy cylinder heads, either lifting off the engine or simply moving around? Ever ruined an EXPENSIVE multi-layer head gasket while trying to install a cylinder head due to no secure way to hold it without two people. We answered yes to all of those things, and came up with a tool for anyone that works on BMWs often, and needs a way to simply, and easily remove/install, or simply move around a cylinder head. These cylinder head tools are machined from a solid billet of 6061-T6 aluminum and anodized in 4 colors for long-lasting corrosion resistance. They are knurled for non-slip grip when oily or wet, and positioned so the head is balanced when lifting The Head Handler fits the following engines, N54, N55, S55, B58 and we offer short extensions for installation with no cams/Cam ledges on the head, or long extensions for people that want to install or remove a head with cams still installed. (B58 only requires short extensions) -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewCNC N54/N55 Single Flange
$329.99 – $409.99Price range: $329.99 through $409.99100% CNC flange in mild or SS. This flange will fit all N54's and N55's and comes COMPLETE ready for welding your runners onto it -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT BMW Plug and Play Pre AND Post throttle 5-Bar (58 psi), 6-Bar(72 psi) Map Sensor Kits
$177.49 – $209.99Price range: $177.49 through $209.99Looking to up your boost limit on just about any BMW vehicle that runs a 3 or 4-wire BMW map sensor including but not limited to S58, B58, N54, N55, S55, S63, B48, B47, B42, B57, B46? We were too, so we decided to make a very easy plug-and-play kit for 3, and 4-wire BMW map sensors. These kits will allow you to completely replace the 3-wire sensor with one of our sensors, leave your stock 4-wire in place for IAT sensing, and move the power, ground, and sensor signal from the factory sensor to our sensor. These sensors have the proper scaling which will allow your tuner to simply change your map sensor scaling in the tune, and the factory ECU will be able to utilize the sensor voltage with no problem. We are offering these in 5 bar (58 psi), and 6 bar (72 psi), and each comes with a plug-and-play harness, and optional fittings for ease of installation.Note: For the S58/B58 our Factory style Pre-Throttle map sensor is also 5 bar, and will work fine coupled with the post throttle kit, but the scaling is different, if you want matching Voltages Pre/Post throttle you can run two of these.
A variety of install pics can be found below and - Here
Scaling PDF Links: 5-Bar / 6-Bar
Features include:- Plug and Play harnesses with no wire splicing
- Output wire for connecting a PI or external controller to your post-throttle map sensor for the most stable signal that is not affected by throttle closure
- Different fittings are available for your plumbing needs.
- Can have matching voltage signals for pre/post throttle for ease of tuning, and boost reference
- B58/S58 etc Pre Throttle - 3 Wire Harness (Charge pipe to 1/8" NPT adapter needed, for B58/S58 90 degree adapter needed to provide sensor clearance)
- B58/S58 Post Throttle - 4 Wire Harness (Boost reference will be needed from manifold to sensor)
- F90 M5 Pre/PostĀ Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- Most all other platforms Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- B58
- S58
- S63/ S63TU
- N63
- N54
- S55
- N55
- N20
- B46
- B48
- B57
- B47
-
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT-FAB Billet Velocity Stack
$35.69 – $45.89Price range: $35.69 through $45.89Running an open turbo, and want to straight out the airflow to the compressor for extra efficiency. Our billet velocity stack is what you need. Backed by physics a Bellmouth or velocity stack will help smooth the air coming into the turbocharger or on NA cars. These are made from 6061-T6, and anodized in a variety of colors and sizes. Currently, we offer 3", 4", and 5" These are suitable to fit any intake tubing or turbocharger inlet with that size. These are available with or without a silicone connector and clamps. Our V-Stacks are also made to extend down on the outside so you can attach a Vibrant S&B or other compatible 7" Filter on the 3"/4" version. Features:- Smooth air before it enters the turbocharger or Intake
- Very low profile, only sticking 2.5" above the turbocharger inlet. Even if you have no room for a filter these will fit
- Fits all turbochargers with a 3", 4" or 5" inlet including PTE Sportsman Cover!
- 3" and 4" version works with Vibrant #10961 7" filter or S&B 1032 FilterĀ if you have room
- 100% billet construction for high-strength
- Anodized for long life, and durability
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Brake Kits Rotors/Hats only
$117.49 – $262.49Price range: $117.49 through $262.49This is for those running our brake kits that use our 11.75" or 13" Rotors that want to easily change between rotors for dedicated drag racing and street use. You can now buy Rotor/Hat Assemblies by themselves to switch between any of our 3 optionsThe price is for ONE ROTOR / OR ONE ROTOR/HAT ASSEMBLY
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT E/F Series BMW Ultimate Front Drag Brake Kit
$1,399.99 – $1,949.99Price range: $1,399.99 through $1,949.99Looking to make your E/F Series BMW faster in the 1/4 mile or 1/2 mile racing? Want to run 17" or 15" wheels in the front? Want to drop OVER 54lbs of unsprung weight off the front of the car at the same time? Do not want to break the bank while doing so? Look no further than the VTT Ultimate Front Drag kit for the E/F Series BMWs. This kit will allow you to run the wheel/tire combo you need to drop your ETs all while putting the car on a significant diet over the stock front brake setup. The kit is a true plug-and-play kit using Genuine VTT parts, coupled with DOT-approved brake lines, CNC 7075 rotor hats/brackets, and a CEL eliminator harness for the brake sensor. This kit comes in 1 variation, with two different caliper Options for each. We HIGHLY suggest 6-piston Calipers for street driving and 1/2 mile racing. These calipers will drop weight, AND be a braking upgrade over stock calipers. -
Sale!Quick View
PFS Bucketless Double Shot Fuel Pump Upgrade
$649.99Original price was: $649.99.$552.49Current price is: $552.49. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Reinforced Universal Silicone Hoses
$11.99 – $15.99Price range: $11.99 through $15.99VTT offers silicone hoses in various Push-lock sizes, we use these for our catch can kits, but they are also suitable for coolant, vacuum, boost, etc. Do not use with fuel. We offer: -10 Push Lock 24", and 18" -8 Push Lock 24", and 19.5" -6 Push Lock 24" -
Sale!Quick View
Black Tial BOV Spring
$52.49Original price was: $52.49.$49.87Current price is: $49.87.If running a Tial BOV on your N54 instead of the TurboSmart Raceport you want to run the black spring. This will provide you with the most complete vent, and eliminate any chance for flutter/surge. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT E9/8X Rear Drag Brake Conversion Kit
$949.99 – $1,069.99Price range: $949.99 through $1,069.99VTT ultimate E8/9X ultimate rear brake conversion kit
Ā VTT is happy to announce its new rear brake conversion kits for the E8X/E9X platforms. We take what already exists on the market, and make it much more complete, and much more performance-oriented while keeping the clearance for those 15ā wheels. This kit replaces your rear brake rotors and calipers to fit 15" wheels. It includes lightweight Wilwood calipers to go from the single-piston factory caliper to race-inspired 4 Piston calipers. While dropping up to a whopping 20 LBS of unsprung weight off the back of your vehicle!
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Cone Filters
$41.99 – $53.99Price range: $41.99 through $53.99VTT Cone Filters feature High flow elements with a silicone body and a velocity stack built-in for smooth flow. We offer these filters in a variety of sizes for universal use. These are also replacement filters for VTT intake kits including B58 Gen 1,Ā TU, Supra, Audi 4.0, N54 Dual Cone filter kit, etc Kit Includes:- 1 - Cone Filter
- 1 - Clamp
-
Sale!Quick View
PFS Single Shot LPFP
$589.99Original price was: $589.99.$501.49Current price is: $501.49. -
Sale!Quick View
PFS Bucketless Single Shot Fuel Pump Upgrade
$409.99Original price was: $409.99.$348.49Current price is: $348.49. -
Quick View
N54 “GC LITE 2.0” Stock location Turbocharger Kit
From: $2,619.99We are proud to introduce the latest in our line of N54 turbocharger products the VTT "GC LITE" 2.0 turbochargers.WHP Level supported (with proper fuel, upgrades, and tuning) Stock-700WHP -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT HIGH-FLOW -16 Catch Can System
$499.00 – $649.00Price range: $499.00 through $649.00VTT -16 Billet HIGH-FLOW Catch Can System
Maximum Venting for Maximum Power
VTT is proud to introduce our -16 Billet High-Flow Catch Can System ā designed from the ground up for high-horsepower applications requiring serious crankcase ventilation. Whether you're pushing over 900WHP or beyond 2000WHP, this system delivers unmatched performance, reliability, and engine bay cleanliness.
Key Features:
-
Supports -16 AN lines (with optional -12 or -20 fittings)
- 20 Fluid OZ capacity
-
Engineered for big-power builds needing high crankcase pressure relief
-
Triple-stage filtration system to eliminate oil mist ā even in the event of engine failure
-
Designed, tested, and proven to keep oil inside the catch can ā not in your engine bay
Triple Filtration Technology:
-
Stage 1 - Stainless steel filter ā captures 95% of oil mist on entry
-
Stage 2 - Perforated diffuser plate ā further disperses and slows down airflow
-
Stage 3 - Final stainless mesh layer ā scrubs out any remaining vapor before venting
This advanced system has been tested with over 200 PSI of pressure and more than half a quart of oil without releasing a trace of oil mist. As long as the catch can is properly serviced and not overfilled, even catastrophic engine failure wonāt result in a mess under your hood.
Application-Specific Kits Available:
We offer plug-and-play kits for popular platforms, including:
-
G8X M2/M3/M4 (S58) SINGLE TURBO ONLY
-
F9X X3M/X4M SINGLE SINGLE TURBO ONLY
-
A9X Toyota Supra
Each kit includes everything needed for installation: catch can, vehicle-specific bracket, fittings, hoses, and optional drain. Again: Plug-and-play kits include ALL required parts. Bracket, fittings, line, etc. No additional fittings are required except the drain if wanted.
-
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsNeed a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
Quick View
PFS POD HPFP Upgrade
$1,219.99The PFS POD (Planetary OverDrive) is an Overspeed gearbox for your N54/early N55 high-pressure fuel pump.Ā Mechanical fuel pump flow potential is a function of shaft speed -spin it faster, get more fuel flow.Ā The PFS POD allows the user to increase the shaft speed 3x, drastically increasing the output capability of a stock N54 HPFP, and avoid the issues of implementing Port Injection and/or Methanol Injection on vehicles that are targeting more power than the stock fuel system can supply. -
Quick View
VTT/PFS Stainless Steel Fuel Strainer for Walbro In-Tank Pumps
The fuel system is one of the most critical components of your entire buildāit delivers the fuel that translates into big power and fast times! Without proper filtration, your Walbro 274, 285, or 295 fuel pump can ingest contaminants, leading to premature failure. However, choosing the right strainer or pre-filter is just as important as post-filtration. šØ Why Does Your Fuel Pump Need the Right Strainer? ā Too fine of a filter can restrict flow and cause the inlet to collapse. ā Too coarse of a filter can allow debris to pass through, damaging the pump and engine. ā Low-quality materials can break down, collapse, or cause fueling issuesāleading to potential engine failure.The VTT/PFS Stainless Steel Fuel Strainer ā The Ultimate Solution
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewReplacement Brake Pads for VTT Brake Kits
$69.99 – $209.99Price range: $69.99 through $209.99 -
Sale!Quick View
PFS Double Shot LPFP
$819.99Original price was: $819.99.$696.99Current price is: $696.99. -
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT “DCS” EWG System for TurboSmart Straight Gates
$755.99 – $1,421.99Price range: $755.99 through $1,421.99VTT is proud to offer our EWG "Direct Control System" or DCS! This is a completely new innovation for people looking to control the highest-flowing wastegate on the market using an existing BMW electronic actuator. This system will allow BMW owners who have a vehicle with Electronic Wastegates from the factory to utilize this system to control an externally wastegated turbo system, AND it will ALSO allow ANY vehicle to use this setup to control your own custom turbo system. This is done by utilizing our custom 7075 Billet aluminum bracket coupled with a Turbosmart Straight gate, and if needed an EWG controller made for us by DCCD Pro. This allows direct external wastegate control over any turbocharger system with or without EWG for the factory. Features:- Utilizes the most current wastegate technology the Turbosmart Straight Gate. This gate allows maximum flow with minimal restriction, low drive pressure, and much more. Full details can be found here - https://www.turbosmart.com/product/electronic-straightgate-esg50-external-wastegate/
- Can be configured in multiple ways, and angles based on how you mount the adapter
- The adapter is 7075 Aluminum which has the strength of steel and weight of aluminum
- All connection fittings, are made from Nitronic 60 which has extremely high temperature and wear properties
- Zero Drive Pressure, no springs, no poppet valves, direct control over the gate using factory ECU logic
- Adaptable to ANY turbo system on any car to provide the ultimate in boost control!
-
Sale!Quick View
VTT BMW E9/8X Double Adjust Drag Shock Kit
$1,169.99Original price was: $1,169.99.$1,052.99Current price is: $1,052.99.Looking to maximize your E9/8X Series BMW for drag racing? Want to be able to dial in the perfect amount of compression or rebound on your launch? The VTT Double adjust drag shock kit is just want the doctor ordered! -
Quick ViewN54 Specific bracket for our Midual VTT catch cans. This is for the Dual can version. Mounts to the driver side strut bar.
-
Quick ViewThis is the same as our N54 OCC brackets except the tabs are bent at a 90-degree angle to make for mounting to any flat surface.
-
Sale!Quick View
External HPFP Controller for Secondary HPFP
$389.99Original price was: $389.99.$370.49Current price is: $370.49. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT-FAB Carbon Fiber Turbo Blanket
$69.99 – $104.99Price range: $69.99 through $104.99Looking to keep the underhood heat down on your single turbo car, or build? We got you covered with our VTT-FAB Carbon Fiber Turbo Blankets. The outer shell is made of Carbon Fiber, and the inner shell is Silica Fiber. For 2500F intermittent / 1800 direct heat rating. We have them in 2 sizes T3, and T4. See fitment below Kit included:- 1 Carbon Blanket of choice
- 2 install springs
-
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT E90 Carbon Fiber Headlight Duct
$548.99 – $602.99Price range: $548.99 through $602.99VTT Carbon Fiber headlight duct for the E90 will complete any racecar or streetcar build helping to get rid of weight and add functionality with a working 6ā³ velocity stack to run your turbocharger into for optimal flow, and ram air. 100% multi-layer prepreg Carbon Fiber, with a UV resistant clear coat for the ultimate in strength, and durability! We offer them in the following varieties: Passenger side duct with 6ā³ Velocity stack 3ā³ hose connection Passenger side duct with 6ā³ Velocity stack 4ā³ hose connectionFITMENT: PLEASE NOTE IT FITS ALL E90, AND E91 MODELS INCLUDING M3, ETC. THIS LIGHT HAS NOT BEEN TEST FIT ON AN LCI VEHICLE, AND WE CAN NOT CONFIRM IT FITS LCI. WE CAN ONLY CONFIRM PRE-LCI FITMENT AT THIS TIME.
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Billet Non-Marring Double Ended AN wrenches
$12.99 – $149.99Price range: $12.99 through $149.99Secure Your AN Fittings the Right Way ā Without the Damage
VTT now offers a complete line of precision Billet 6061-T6 Aluminum AN Wrenches, designed to grip without marring your fittings. Whether you're working with -3 or -20 AN sizes, we've got you covered.These wrenches are lightweight, durable, and anodized in 8 vibrant colors for a long-lasting finish and easy size identification.
Available Options:
-
Full Kit: Includes all sizes from -3 to -20
-
Common Size Kit: Includes -4, -6, -8, -10, and -12
-
Individual Wrenches: Purchase only the sizes you need
-
-
Sale!Out of stockQuick View
Plazmaman N54 Intake Manifold
$2,039.99Original price was: $2,039.99.$2,038.96Current price is: $2,038.96. -
Sale!Quick View
N54 USB to Serial for HPFP controller (FTDI Chipset)
$37.99Original price was: $37.99.$36.09Current price is: $36.09. -
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT X PFS “EBS” External Brushless System – 2500HP Capable
$2,379.99 – $2,719.99Price range: $2,379.99 through $2,719.99VTT x PFS EBS (External Brushless System) Fuel System
VTT, in collaboration with Performance Fueling Solutions (PFS), is proud to introduce the PFS EBS ā External Brushless System.
The EBS is a fully stand-alone, next-generation brushless fuel system available in both platform-specific and universal fitments. Built around state-of-the-art Protec brushless pump technology, this system is capable of supporting up to 2,500 HP on ethanol-based fuels ā and even more on gasoline or ethanol blends.
With its compact 15" x 10" footprint and ultra-lightweight construction, the PFS EBS is engineered for performance without compromise. The complete system ā including pumps, surge tank, FPR, controllers, and wiring harness ā weighs in at under 10 lbs (dry), thanks to a carbon fiber mounting plate and carefully chosen lightweight materials.
EBS Bench Testing Video:
EBS Bench Test Video -
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVTT is happy to offer our very unique and universal billet mount to fit any roll bar or cage withĀ 1.5", 1.75", or 2" diameter tubing. These mounts are designed from 6061-T6 aluminum and are made to SECURELY hold a JBL Flip version 3 - Version 6 and allows you to bring music into your race car, off-road vehicle, rock crawler, boat, basically anything that has a length of tubing this will allow you to have an easy way to have tunes without having to install and mount a stereo system. They can also be used as a single mount to hold things such as a helmet, steering wheel, or anything you want to quickly hang for easy access once seated. For the JBL flip you will need TWO mounts, simply install them loosely, snap in your JBL Flip to get the proper spacing, and tighten down. The device is then securely mounted and can be removed easily. We offer these in a variety of anodized colors for a long-lasting durable finish including Black, Red, Blue, Clear, Orange, and Green Mounts are sold individually Features:- Billet 6061-T6 Aluminum construction anodized in a variety of colors
- Can be used to SECURELY mount a JBL Flip 3-6 to anything that has a length of 1.5", 1.75" or 2" tubing
- Can also be used as a universal mount for anything you need to hang in your race car, off-road vehicle, etc
- Completely reversible, and can be moved from vehicle to vehicle
-
Quick ViewAdding a Front-facing manifold to your N54, and need to extend your map sensor harness? We got you covered with ur 24" extension harness. High-quality wiring, with seating, and our own 3D printed connectors ensure a perfect fit.
-
Quick ViewShow off your VTT support and get a good laugh from people with our "We Like To Party" License plate bracket. Born from the infamous quote in Talladega nights
-
Quick ViewAll new design for 2018! We are proud to introduce the latest in our line of N54 turbocharger products the VTT "GC" 2.0 turbochargers. This is a new N54 turbocharger from the ground up, using 100% new parts throughout.
-
Quick View
VTT 600 Power Pack
From:$3,699.97Original price was: $3,699.97.$3,599.47Current price is: $3,599.47. -
Quick View
VTT 700 Power Pack
From:$4,281.96Original price was: $4,281.96.$4,145.46Current price is: $4,145.46. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewN54 Dual Flanges
$329.99 – $409.99Price range: $329.99 through $409.99Built to order. Lead times vary -
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewN54 Stage 3 VTT VTR (Limited Fitment)
$9,094.44 – $9,688.14Price range: $9,094.44 through $9,688.14WHP Level supported (with proper fuel, upgrades, and tuning) 500 - 800WHP -
Out of stockQuick View
Shotgun Double Barrel N54
$1,289.99 – $1,519.99Price range: $1,289.99 through $1,519.99 -
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewN54 Stage 3 VTT VTX-R (Limited Fitment)
$8,960.39 – $9,285.29Price range: $8,960.39 through $9,285.29WHP Level supported (with proper fuel, upgrades, and tuning) 500 - 900WHP
Product categories
- 10% Max Discount
- 15% Max Discount
- BMW
- Diesel
- Dodge V8 Platforms
- Ford
- Honda
- Hurricane I6
- Mercedes
- Mitsubishi
- N/S63TU
- No Discount Products
- Porsche
- Powersports
- Tier OBD
- Toyota
- Uncategorized
- Universal
- VTT
- VTT-FAB
- VTTEV
- VW/VAG