-
Quick ViewLooking to go above 45 psi in your BMW-powered vehicle? Looking for a plug-and-play solution? We have you covered with our BMW 5 bar sensor. These will allow 58 psi to be read and are factory plug-and-play. Simply remove your old sensor, replace it with the 5 bar, and have your tuner rescale your map values in both your DME tune and your PI tune if applicable.
These are GENUINE BMW sensors directly from BMW.
PLEASE NOTE: These are GENUINE BMW sensors directly from THE BMW DEALERSHIP, BMW IS PUTTING A BMW STICKER OVER A DENSO BOX, AND SELLING THEM. THESE DO NOT HAVE BMW STAMPS ON THEM. WE HAVE ZERO CONTROL OVER THIS.
-
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewPFS A90/91 Toyota Supra Drop in Brushless LPFP upgrade (800-1000WHP+ Capable)
$943.49 – $1,317.49Price range: $943.49 through $1,317.49PFS is proud to offer a true drop-in 800-1000WHP+ capable LPFP for A90/91 Toyota Supras. This LPFP needs NO additional pumps, wiring harnesses, etc etc. It will support up to 800WHP on Ethanol percentages as high as E98 and will support much higher power levels with less E content as long as you have the octane to support it. For the pump, we start with a factory bucket, we modify it extensively to accept our custom PFS Brushless fuel pump. We then re-terminate the factory wiring to accept the new pump. No wiring splices, done the same way the factory does -the right way. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT B58/S58 Head Port Block-Off Kit or Billet check valve kit
$29.99 – $69.99Price range: $29.99 through $69.99VTT B58/S58 Head Port Block-Off / Built Check Valve Kit
The VTT B58/S58 Head Port Block-Off / Check Valve Kit is designed to either seal off or convert the factory head ports used by the OEM low-side PCV system. These ports in the cylinder head utilize engine vacuum to evacuate crankcase gases ā but in the process, can allow oil to enter the intake manifold, leading to valve carbon buildup and other performance issues over time.
This kit provides two configuration options:
-
Block-Off Version ā Completely seals the factory head ports to prevent oil intrusion and unwanted vacuum leaks.
-
Billet Check Valve Version ā Converts the head ports into a robust internal PCV system using precision-engineered check valves. These one-way valves allow vacuum to function as intended while blocking boost pressure from entering the crankcase or charge tract.
By bypassing the factory PCV valve in the valve cover, the VTT kit replaces it with an improved three-valve internal system integrated directly into the cylinder head. This design improves reliability, simplifies plumbing, and ensures consistent crankcase pressure management ā critical for both stock and high-performance B58/S58 applications. This kit does NOT require any tapping, meaning no metal to get into the engine etc. You simply tap the plugs or check valves into place.
Key Features
-
Eliminates oil draw-through into the intake manifold
-
Prevents carbon buildup on intake valves
-
Converts to an internal, head-integrated PCV system
-
Utilizes precision-machined check valves for boost sealing
-
Fully reversible ā Block-offs or valves can be removed if needed
- No tapping is required. Easy install, by tapping the blocks or valve into place.
-
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT B58 TU BILLET CNC Valve Cover
$1,769.99VTT Billet Aluminum Valve Cover ā B58 TU
The Only Billet Valve Cover Option for the B58 TU Platform VTT is proud to introduce our B58 TU Billet Aluminum Valve Cover, designed for enthusiasts looking to enhance both the performance and appearance of their engine bay. The OEM plastic valve cover is known to crack over time and contains a problematic built-in PCV system. Our billet cover eliminates those issues and gives you complete modularity and control over your PCV setup. We recommend pairing it with our B58 TU Catch Can Kit for the ultimate crankcase ventilation solution. Additional breather optionsāincluding our oil cap breather and one-way stainless breathersāare also available to further enhance your setup.
š§ Key Features:
- ā 100% CNC-Machined 6061-T6 Aircraft-Grade Aluminum
- ā Anodized in a variety of durable color options
- ā Lightweight at 9.7 lbs (vs. 7.9 lbs for the stock plastic cover)
- ā Includes three shrouded -10 ORB ports for maximum PCV flexibility
- ā Fully baffled ports to reduce oil carryover
- ā Only billet option on the market for B58 TU
- ā Optional Titanium hardware or OEM-style fasteners
-
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewPFS B58 Port Injection Kit
$620.49 – $2,022.99Price range: $620.49 through $2,022.99Looking for some more fuel for your B58 powered BMW? Not looking to break the bank on overpriced PI kits? PFS has you covered with its Plug, and play PI kit for the B58. -
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT B58 Gen 1 BILLET CNC Valve Cover
$1,449.99 – $1,879.99Price range: $1,449.99 through $1,879.99VTT B58 Gen 1 Billet Aluminum Valve Cover
Performance, Reliability, and Style for Your B58 Engine VTT is proud to release our Billet Aluminum Valve Cover for the B58 Gen 1 platform. Designed for B58 owners looking to enhance engine bay aesthetics while addressing the limitations of the factory plastic valve cover, this upgrade is a functional and visual game-changer. The OEM plastic cover is known to crack with age and mileage, and its built-in PCV system often causes issues. Our billet cover eliminates these problems and gives you full control over your PCV setup. We recommend pairing it with our B58 Catch Can Kit for maximum performance and crankcase pressure management. For additional crankcase venting, we offer multiple breather options, including a one-way stainless breather and our popular oil cap breather.
š§ Key Features:
- ā 100% CNC-Machined from 6061-T6 Aircraft-Grade Aluminum
- ā Available in a range of anodized color options
- ā Lightweight ā 9.7 lbs (vs. 7.9 lbs for OEM ā just a 1.8 lb difference)
- ā Fully baffled ports to minimize oil escape and maximize performance
- ā The only billet option currently available on the market for the B58 Gen 1
- ā Fully modular to suit any PCV configuration you want to run
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT G20/G21/G22/G23 BMW Modular Silicone Intake System
$127.49 – $669.99Price range: $127.49 through $669.99VTT Modular Silicone/Billet Intake System ā BMW G2/3/4X B58TU
VTT is proud to announce our Modular Silicone/Billet Intake System for the BMW G2/3/4X platforms equipped with the B58TU engine.
After extensive testing and countless hours of fitting, weāve created an intake system that delivers both optimized airflow and factory-level fitment.
Why Upgrade?
The factory BMW airbox itself performs well, but the intake tract down to the turbo is full of twists, turns, bellows, and even a built-in silencer that restricts flow and robs power. Our system eliminates these bottlenecks and replaces them with a 3"ā3.5" free-flowing silicone intake tube, paired with either:
-
The stock airbox (for OEM appearance and sound), or
-
Our 6" high-flow cone filter with integrated velocity stack (for maximum airflow and sound).
From testing, weāve confirmed the stock airbox is capable of supporting up to 700WHP. Beyond that, we recommend stepping up to the 6" cone filter system.
-
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT-FAB Extension Harnesses
$49.99 – $104.99Price range: $49.99 through $104.99Need to move your coolant expansion tank to the other side of the vehicle for a single turbo kit you are building, extend Map sensor plugs, or IAT, how about Throttle Body? Don't cut your factory wires. Just get a VTT-FAB extension harness, and plug and play! These come in various lengths and are covered in expanded sheathing with heat shrink on both ends for a long-lasting, good-looking finish. Available:- Coolant Extension for late model BMW 2015+ 5 ft
- Pre-Throttle Map sensor extension harness 2 ft
- Pre-Throttle IAT Sensor extension harness 2 ft
- B58/S58/B48 etc Throttle body extension harness 2 ft
- B58 to S55 Throttle conversion/extension harness 2 ft
- EWG Actuator Extension harness, Various Lengths
- N54 stock MAP to N20 Map sensor extension
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT BMW Plug and Play Pre AND Post throttle 5-Bar (58 psi), 6-Bar(72 psi) Map Sensor Kits
$177.49 – $209.99Price range: $177.49 through $209.99Looking to up your boost limit on just about any BMW vehicle that runs a 3 or 4-wire BMW map sensor including but not limited to S58, B58, N54, N55, S55, S63, B48, B47, B42, B57, B46? We were too, so we decided to make a very easy plug-and-play kit for 3, and 4-wire BMW map sensors. These kits will allow you to completely replace the 3-wire sensor with one of our sensors, leave your stock 4-wire in place for IAT sensing, and move the power, ground, and sensor signal from the factory sensor to our sensor. These sensors have the proper scaling which will allow your tuner to simply change your map sensor scaling in the tune, and the factory ECU will be able to utilize the sensor voltage with no problem. We are offering these in 5 bar (58 psi), and 6 bar (72 psi), and each comes with a plug-and-play harness, and optional fittings for ease of installation.Note: For the S58/B58 our Factory style Pre-Throttle map sensor is also 5 bar, and will work fine coupled with the post throttle kit, but the scaling is different, if you want matching Voltages Pre/Post throttle you can run two of these.
A variety of install pics can be found below and - Here
Scaling PDF Links: 5-Bar / 6-Bar
Features include:- Plug and Play harnesses with no wire splicing
- Output wire for connecting a PI or external controller to your post-throttle map sensor for the most stable signal that is not affected by throttle closure
- Different fittings are available for your plumbing needs.
- Can have matching voltage signals for pre/post throttle for ease of tuning, and boost reference
- B58/S58 etc Pre Throttle - 3 Wire Harness (Charge pipe to 1/8" NPT adapter needed, for B58/S58 90 degree adapter needed to provide sensor clearance)
- B58/S58 Post Throttle - 4 Wire Harness (Boost reference will be needed from manifold to sensor)
- F90 M5 Pre/PostĀ Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- Most all other platforms Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- B58
- S58
- S63/ S63TU
- N63
- N54
- S55
- N55
- N20
- B46
- B48
- B57
- B47
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT HIGH-FLOW -16 Catch Can System
$499.00 – $649.00Price range: $499.00 through $649.00VTT -16 Billet HIGH-FLOW Catch Can System
Maximum Venting for Maximum Power
VTT is proud to introduce our -16 Billet High-Flow Catch Can System ā designed from the ground up for high-horsepower applications requiring serious crankcase ventilation. Whether you're pushing over 900WHP or beyond 2000WHP, this system delivers unmatched performance, reliability, and engine bay cleanliness.
Key Features:
-
Supports -16 AN lines (with optional -12 or -20 fittings)
- 20 Fluid OZ capacity
-
Engineered for big-power builds needing high crankcase pressure relief
-
Triple-stage filtration system to eliminate oil mist ā even in the event of engine failure
-
Designed, tested, and proven to keep oil inside the catch can ā not in your engine bay
Triple Filtration Technology:
-
Stage 1 - Stainless steel filter ā captures 95% of oil mist on entry
-
Stage 2 - Perforated diffuser plate ā further disperses and slows down airflow
-
Stage 3 - Final stainless mesh layer ā scrubs out any remaining vapor before venting
This advanced system has been tested with over 200 PSI of pressure and more than half a quart of oil without releasing a trace of oil mist. As long as the catch can is properly serviced and not overfilled, even catastrophic engine failure wonāt result in a mess under your hood.
Application-Specific Kits Available:
We offer plug-and-play kits for popular platforms, including:
-
G8X M2/M3/M4 (S58) SINGLE TURBO ONLY
-
F9X X3M/X4M SINGLE SINGLE TURBO ONLY
-
A9X Toyota Supra
Each kit includes everything needed for installation: catch can, vehicle-specific bracket, fittings, hoses, and optional drain. Again: Plug-and-play kits include ALL required parts. Bracket, fittings, line, etc. No additional fittings are required except the drain if wanted.
-
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsNeed a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
Quick ViewVTT is proud to offer a Phenolic spacer for the BMW B58 platform. When upgrading to an aluminum charge cooler you get the benefit of a better core, and more cooling capacity, but it also comes with the downside of DIRECT heat transfer from the head to the manifold which can cause heat soak and less-than-ideal IAT's even with an upgraded charge cooler. We manufacture these from G11 Expoxy sheet which has great heat and hardness characteristics, and we feel is the ideal material for this application. The thickness is 8mm.
Please note: Longer studs or bolts may be required introducing a phenolic spacer into your system
-
Quick View
VTT/PFS Stainless Steel Fuel Strainer for Walbro In-Tank Pumps
The fuel system is one of the most critical components of your entire buildāit delivers the fuel that translates into big power and fast times! Without proper filtration, your Walbro 274, 285, or 295 fuel pump can ingest contaminants, leading to premature failure. However, choosing the right strainer or pre-filter is just as important as post-filtration. šØ Why Does Your Fuel Pump Need the Right Strainer? ā Too fine of a filter can restrict flow and cause the inlet to collapse. ā Too coarse of a filter can allow debris to pass through, damaging the pump and engine. ā Low-quality materials can break down, collapse, or cause fueling issuesāleading to potential engine failure.The VTT/PFS Stainless Steel Fuel Strainer ā The Ultimate Solution
-
Quick View
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-Boost Crankcase Ventilation Adapter for BMW Engines Building or running a high-boost, high-powered BMW engine? Boost increases crankcase pressure, which, if left unchecked, can lead to issues such as smoking, power loss, and even engine failure. Adequate venting is essential for optimal performance and engine health. These are designed to connect directly to S58/B58(TU) stock VC, or screw into ANY VTT Billet or Cast VC While some believe a -10AN vent is sufficient for these builds, the truth is: itās not. To address this, we developed a larger, more effective solution for our buildsānow available for everyone. Our Oil CapĀ adapter securely snaps in place, replacing your oil cap and providing a platform for a -16ORB fitting in a variety of configurations. Choose from -12AN to -20AN fittings, depending on your buildās needs. This cap is thicker than our low-profile option so care must be taken when planning hood clearance for the versatile venting options.Key Features:
- Attractive Oil cap design
- Connects to stock S58/B58(TU) VC or VTT Billet/Cast VC
- Vented, comes with multi-hole venting to knock down large oil droplets before they make their way into the catch can system
- High-performance venting: Supports configurations from -12AN to -20AN fittings.
- Customizable: Compatible with various fittings to suit your build.
Important Notes:
- This kit requires you to supply your own hose, hose ends, and catch can to complete the system.
- Some fitting options may require 4ā5 days for shipping, as we keep only select configurations in stock.
- Also fits other platforms such as B48, B46, Mini, etc. DOES NOT FIT Gen 1 B58
-
Sale!Quick View
VTT Billet B58 (TU) HMM (Coolant Unit) Delete kit
$249.99Original price was: $249.99.$199.99Current price is: $199.99.VTT B58 (TU) HMM Delete Plate
Looking to build a race car with a B58 engine?
Doing a B58 swap and donāt want the complicated BMW Heat Management Module (HMM)?
Need a simple -16AN or -20AN line setup instead of the factory tangle?If so, the VTT B58 (TU) HMM Delete Plate is exactly what you need.
This kit eliminates the bulky OEM Heat Management Module and replaces it with a clean billet block-off solution. The included rear water pump plug and hold-down bracket ensure proper sealing, while the modular -16ORB port allows you to run your choice of -16AN, -20AN, or any compatible fitting. Build your lines, run them to the radiator, add an inline thermostat if desired ā and enjoy a vastly simplified, race-ready B58 cooling system.
-
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT Billet Non-Marring Double Ended AN wrenches
$12.99 – $149.99Price range: $12.99 through $149.99Secure Your AN Fittings the Right Way ā Without the Damage
VTT now offers a complete line of precision Billet 6061-T6 Aluminum AN Wrenches, designed to grip without marring your fittings. Whether you're working with -3 or -20 AN sizes, we've got you covered.These wrenches are lightweight, durable, and anodized in 8 vibrant colors for a long-lasting finish and easy size identification.
Available Options:
-
Full Kit: Includes all sizes from -3 to -20
-
Common Size Kit: Includes -4, -6, -8, -10, and -12
-
Individual Wrenches: Purchase only the sizes you need
-
-
Sale!Quick View
VTT Billet B58/S58 HPFP Block off plates
$129.99Original price was: $129.99.$99.99Current price is: $99.99.VTT B58/S58 HPFP Block-Off Plate Kit
If youāre converting your B58 or S58 build to port injection (PI) only and removing the direct injection (DI) system and high-pressure fuel pumps (HPFPs), youāll need to properly seal the HPFP ports in the valve cover.
Our billet aluminum block-off plates provide a simple, clean solution.
Just remove the HPFP and cam follower, then install the plate ā it seals the valve cover and eliminates the HPFP cleanly and securely.Please Note:
-
Removing the HPFP typically requires a standalone ECU.
-
If youāre only removing a single HPFP (such as on the S58), a tune adjustment will be necessary for proper operation.
-
-
Sale!
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick ViewVTT X PFS “EBS” External Brushless System – 2500HP Capable
$2,379.99 – $2,719.99Price range: $2,379.99 through $2,719.99VTT x PFS EBS (External Brushless System) Fuel System
VTT, in collaboration with Performance Fueling Solutions (PFS), is proud to introduce the PFS EBS ā External Brushless System.
The EBS is a fully stand-alone, next-generation brushless fuel system available in both platform-specific and universal fitments. Built around state-of-the-art Protec brushless pump technology, this system is capable of supporting up to 2,500 HP on ethanol-based fuels ā and even more on gasoline or ethanol blends.
With its compact 15" x 10" footprint and ultra-lightweight construction, the PFS EBS is engineered for performance without compromise. The complete system ā including pumps, surge tank, FPR, controllers, and wiring harness ā weighs in at under 10 lbs (dry), thanks to a carbon fiber mounting plate and carefully chosen lightweight materials.
EBS Bench Testing Video:
EBS Bench Test Video -
Quick ViewHigh-Boost Crankcase Ventilation Adapter for S58/B58 Engines Building or running a high-boost, high-powered S58 or B58 engine? Boost increases crankcase pressure, which, if left unchecked, can lead to issues such as smoking, power loss, and even engine failure. Adequate venting is essential for optimal performance and engine health. While some believe a -10AN vent is sufficient for these builds, the truth is: itās not. To address this, we developed a larger, more effective solution for our buildsānow available for everyone. Our low-profile adapter securely snaps in place, replacing your oil cap and providing a platform for a -16ORB fitting in a variety of configurations. Choose from -12AN to -20AN fittings, depending on your buildās needs. At just 10mm thick, this adapter maximizes hood clearance for versatile venting options.
Key Features:
- Low-profile design: Only 10mm thick for maximum hood clearance.
- High-performance venting: Supports configurations from -12AN to -20AN fittings.
- Customizable: Compatible with various fittings to suit your build.
Important Notes:
- This kit requires you to supply your own hose, hose ends, and catch can to complete the system.
- Some fitting options may require 4ā5 days for shipping, as we keep only select configurations in stock.
- Also fit other platforms such as B48, B46, Mini, etc. DOES NOT FIT Gen 1 B58
Product categories
- 10% Max Discount
- 15% Max Discount
- BMW
- Diesel
- Dodge V8 Platforms
- Ford
- Honda
- Hurricane I6
- Mercedes
- Mitsubishi
- N/S63TU
- No Discount Products
- Porsche
- Powersports
- Tier OBD
- Toyota
- Uncategorized
- Universal
- VTT
- VTT-FAB
- VTTEV
- VW/VAG